USB转网卡口（usb---RJ-45 interface） 在DOS下加载驱动程序，错误信息
MAC Iint error:could not locate adapter
error loading device driver DM9PCI.dos
error 7306:the driver failed to initialize
DM9PCI.dos was not loaded
error 7321: Network-card drivers failed to load
请各位大哥帮忙看看：其中配置文件内容是
config.sys内容
shell=a:\command.com a:\/e:2048 /p
device=a:\himem.sys /testmem:off
devicehigh=a:\ifshlp.sys
files=35
buffers=35
dos=high,umb
stacks=9,256
lastdrive=z
protocol.ini 内容
[network.setup]
version=0x3110
netcard=ms$DM9PCI,1,MS$DM9PCI,1
transport=ms$nwlink,MS$NWLINK
transport=ms$ndishlp,MS$NDISHLP
lana0=ms$DM9PCI,1,ms$nwlink
lana1=ms$DM9PCI,1,ms$ndishlp
[MS$NWLINK]
FRAME=ETHERNET_802.2
DriverName=nwlink$
BINDINGS=MS$DM9PCI
[protman]
DriverName=PROTMAN$
PRIORITY=MS$NDISHLP
[MS$DM9PCI]
DriverName=DM9PCI$
[MS$NDISHLP]
DriverName=ndishlp$
BINDINGS=MS$DM9PCI
system.ini 内容
[network drivers]
;netcard=e100b.dos
netcard=DM9PCI.dos
transport=ndishlp.sys
devdir=a:
LoadRMDrivers=yes
[Password Lists]
*Shares=a:\Shares.PWL
TESTER=a:\TESTER.PWL
[network]
sizworkbuf=1498
filesharing=no
printsharing=no
autologon=no
lanroot=a:
username=TESTER
workgroup=WORKGROUP
reconnect=yes
dospophotkey=N
lmlogon=0
logondomain=WORKGROUP
preferredredir=full
autostart=full
maxconnections=8
连接文件内容为
PROMPT $p$g
net initialize
if errorlevel 1 goto linkfail
nwlink
if errorlevel 1 goto linkfail
net start
if errorlevel 1 goto linkfail
net logon bekins bekind2 /yes /savepw:no
if errorlevel 1 goto linkfail
cmdelay 5
net use m: /delete
:start
cmdelay 3
net use m: \\computer\monitor < a:\y.key
if not errorlevel 1 goto end
cmdelay 5
net use m: \\computer\monitor < a:\y.key
if errorlevel 1 goto start
goto end
:linkfail
ECHO LAN link fail > %EXDRV%\err.log
:end
各位大哥看看那个地方配置不对，请指教。
MAC Iint error:could not locate adapter
error loading device driver DM9PCI.dos
error 7306:the driver failed to initialize
DM9PCI.dos was not loaded
error 7321: Network-card drivers failed to load
请各位大哥帮忙看看：其中配置文件内容是
config.sys内容
shell=a:\command.com a:\/e:2048 /p
device=a:\himem.sys /testmem:off
devicehigh=a:\ifshlp.sys
files=35
buffers=35
dos=high,umb
stacks=9,256
lastdrive=z
protocol.ini 内容
[network.setup]
version=0x3110
netcard=ms$DM9PCI,1,MS$DM9PCI,1
transport=ms$nwlink,MS$NWLINK
transport=ms$ndishlp,MS$NDISHLP
lana0=ms$DM9PCI,1,ms$nwlink
lana1=ms$DM9PCI,1,ms$ndishlp
[MS$NWLINK]
FRAME=ETHERNET_802.2
DriverName=nwlink$
BINDINGS=MS$DM9PCI
[protman]
DriverName=PROTMAN$
PRIORITY=MS$NDISHLP
[MS$DM9PCI]
DriverName=DM9PCI$
[MS$NDISHLP]
DriverName=ndishlp$
BINDINGS=MS$DM9PCI
system.ini 内容
[network drivers]
;netcard=e100b.dos
netcard=DM9PCI.dos
transport=ndishlp.sys
devdir=a:
LoadRMDrivers=yes
[Password Lists]
*Shares=a:\Shares.PWL
TESTER=a:\TESTER.PWL
[network]
sizworkbuf=1498
filesharing=no
printsharing=no
autologon=no
lanroot=a:
username=TESTER
workgroup=WORKGROUP
reconnect=yes
dospophotkey=N
lmlogon=0
logondomain=WORKGROUP
preferredredir=full
autostart=full
maxconnections=8
连接文件内容为
PROMPT $p$g
net initialize
if errorlevel 1 goto linkfail
nwlink
if errorlevel 1 goto linkfail
net start
if errorlevel 1 goto linkfail
net logon bekins bekind2 /yes /savepw:no
if errorlevel 1 goto linkfail
cmdelay 5
net use m: /delete
:start
cmdelay 3
net use m: \\computer\monitor < a:\y.key
if not errorlevel 1 goto end
cmdelay 5
net use m: \\computer\monitor < a:\y.key
if errorlevel 1 goto start
goto end
:linkfail
ECHO LAN link fail > %EXDRV%\err.log
:end
各位大哥看看那个地方配置不对，请指教。