|
gxllawyer
新手上路

积分 8
发帖 2
注册 2005-11-2
状态 离线
|
『楼 主』:
怎样把windows3.2装入U盘?
使用 LLM 解释/回答一下
有没有什么好方法把windows3.2安装入U盘,并且可以在dos 下作为系统引导盘?请教各位高手。
非常感谢!
Is there any good way to install Windows 3.2 into a USB flash drive and make it bootable as a system under DOS? Asking for advice from all the experts. Thanks a lot!
|
|
2005-11-2 14:45 |
|
|
duoduol
新手上路

积分 2
发帖 1
注册 2005-11-13
状态 离线
|
|
2005-11-14 01:46 |
|
|
jesse1983
初级用户
 
积分 137
发帖 12
注册 2005-6-9
状态 离线
|
|
2006-2-3 20:06 |
|
|
yksoft1
高级用户
   
积分 823
发帖 395
注册 2006-1-28
状态 离线
|
『第 4 楼』:
使用 LLM 解释/回答一下
Win3.2完全安装就20多兆。
U盘最好是USB-ZIP启动的,先装DOS5.0以上系统(要HIMEM,最好要SMARTDRV)可以直接运行,也可以释放到虚拟磁盘运行。
The full installation of Win3.2 is just over 20 megabytes. The USB flash drive is best to be USB-ZIP bootable. First install a DOS system above version 5.0 (HIMEM is required, and SMARTDRV is best). It can be run directly or released to a virtual disk for running.
|
|
2006-2-4 00:21 |
|
|
jesse1983
初级用户
 
积分 137
发帖 12
注册 2005-6-9
状态 离线
|
『第 5 楼』:
使用 LLM 解释/回答一下
要HIMEM需要怎么配置?
SMARTDRV是什么?
我用的是usboot167做的启动盘行吗
How to configure HIMEM?
What is SMARTDRV?
Is the boot disk made with usboot167 okay
|
|
2006-3-12 15:07 |
|
|
rongguoxiang
新手上路

积分 2
发帖 1
注册 2006-6-4
状态 离线
|
『第 6 楼』:
WIN3.2在U盘中运行
使用 LLM 解释/回答一下
可以把能在硬盘上运行的WIN3.2直接拷贝到DOS7.1的启动盘U中,然后修改U盘WINDOWS 目录下的PROGMAN.INI文件,把里面的路径删除只留下文件名。如果内存大的话,可以用XMSDSK.EXE在内存中建立一个虚拟盘,然后用XCOPY把U盘中WINDOWS目录拷贝至虚拟盘中,在虚拟盘中运行WIN.COM即可。
You can copy the WIN3.2 that can run on the hard disk directly to the U disk of the DOS 7.1 boot disk, and then modify the PROGMAN.INI file in the WINDOWS directory of the U disk, deleting the path inside and leaving only the file name. If the memory is large, you can use XMSDSK.EXE to create a virtual disk in the memory, and then use XCOPY to copy the WINDOWS directory in the U disk to the virtual disk, and then run WIN.COM in the virtual disk.
|
|
2006-6-4 14:10 |
|
|
zrh4019
初级用户
 
积分 39
发帖 12
注册 2005-7-24
状态 离线
|
『第 7 楼』:
使用 LLM 解释/回答一下
用USBoot将U盘设为USB-HDD,然后将win3.2安装文件复制到Fat32分区,用U盘启动到DOS,并执行Win3.2的Setup.exe即可,但要注意不要在U盘建立永久交换分区,应该在fat32上建立临时交换文件,否则会很慢。而且别忘了运行share.exe。
我已用此方法试过,非常成功,速度很快。并且Office4.2cn,Microsoft Visual C++,Borland Delphi 1.0 , WinZip6.3 , Microsoft Visual Basic 1.0 - 4.0 都已安装并可以运行!
Use USBoot to set the USB drive as USB-HDD, then copy the Win3.2 installation files to the Fat32 partition, boot to DOS from the USB drive, and execute Win3.2's Setup.exe. But note that do not create a permanent swap partition on the USB drive; instead, create a temporary swap file on the Fat32 partition, otherwise it will be very slow. And don't forget to run share.exe.
I have tried this method and it is very successful, with fast speed. And Office4.2cn, Microsoft Visual C++, Borland Delphi 1.0, WinZip6.3, Microsoft Visual Basic 1.0 - 4.0 have all been installed and can run!
|
|
2006-7-19 18:31 |
|