中国DOS联盟

几天了，DOS下上Internet不知怎样，能PING通，可浏览器不会用，内存也不够，最多只有486K。盼老大或高手能否用VM 或VPC做个教程，谢谢了。

用lynx，很简单，配置好wattcp.cfg就可以了，不要加载不必要的tsr程序，只加载一个packet driver就可以了。

只有TCPTSR（76.78K）和NMTSR（6.16K），试一下用lynx，谢谢你的回答。在VM 或VPC里能否用NET或桥连上Internet。

当然，和真实机器一样。

MS-DOS LAN Manager v2.1 Netbind
Performing Power-Up Autosense...
Switching between 10BaseT and 100BaseTx...
Selected media: 100BaseTx (TP 100) Autosense
Initializing TCP/IP via DHCP....
Microsoft DOS TCP/IP 1.0a
C:\>ping 192.168.0.1
Copyright (c) Microsoft Corporation, 1991-1993. All rights reserved.
Copyright (c) Hewlett-Packard Corporation, 1985-1993. All rights reserved.
Copyright (c) 3Com Corporation, 1985-1993. All rights reserved.
echo received from 192.168.0.1 with roundtrip < 50 msec

VPC5.2Z中用lynx出现 “NO PACKET DRIVER FOUND ”已在config.sys中加载dis_pkt.dos。NDIS2驱动程序怎样转成Packet 。看过http://www.cn-dos.net/forum/viewthread.php?tid=15347，就是不能转成Packet。望能得到详细解答，谢谢了

把你ms network client安装目录下的的system.ini和protocol.ini贴上来。

1.PROTOCOL.INI
[network.setup]
version=0x3110
netcard=DC21X4,1,DC21X4,1
transport=tcpip,TCPIP
lana0=DC21X4,1,tcpip

[TCPIP]
NBSessions=6
DefaultGateway1=
DefaultGateway0=
SubNetMask0=255 255 255 0
IPAddress0=
DisableDHCP=0
DriverName=TCPIP$
BINDINGS=DC21X4
LANABASE=0

[protman]
DriverName=PROTMAN$
PRIORITY=MS$NDISHLP

2.SYSTEM.INI
[network]
sizworkbuf=1498
filesharing=no
printsharing=no
autologon=yes
computername=HXPHH
lanroot=C:\NET
username=HXPHH
workgroup=WORKGROUP
reconnect=yes
dospophotkey=N
lmlogon=0
logondomain=WORKGROUP
preferredredir=basic
autostart=basic
maxconnections=8

[network drivers]
netcard=DC21X4.DOS
transport=tcpdrv.dos,nemm.dos
devdir=C:\NET
LoadRMDrivers=yes

[386enh]
TimerCriticalSection=5000
UniqueDosPSP=TRUE
PSPIncrement=2

[Password Lists]
*Shares=C:\NET\Share000.PWL

PROTOCOL.INI添加以下几行:
DriverName=PKTDRV$ BINDINGS=DC21X4 INTVEC=0X60

原来也加过，但还是不行呀，指定IP地址也不行，试过好多方法都不行，会有“NO PACKET DRIVER FOUND”。是不是已连上，还有什么方法来确认是不是已加载PACKET DRIVER。

从启动信息上看根本就没加载dis_pkt.dos啊。
把dis_pkt.dos行从config.sys里去掉，把dis_pkt.dos拷到net安装目录下，然后修改net目录下的system.ini

netcard=DC21X4.DOS
transport=tcpdrv.dos,nemm.dos,dis_pkt.dos
devdir=C:\NET
LoadRMDrivers=yes

config.sys加载内存也有dis_pkt.dos，现在应该上Internet了（已登录外网FTP服务器），太高兴了，谢谢你。用FTP下载时有“WATTCP” 插口错误，不知什么意思

wattcp.cfg
my_ip = 192.168.0.2
netmask = 255.255.255.0
gateway = 192.168.0.1

还有LYNX的wattcp.cfg也是这样配制的，出现错误。

TITLE: DosLynx Load Error


DOSLYNX LOAD ERROR

Return to Hotlist



DosLynx was unable to load the requested URL.

This could be due to an invalid URL

or due to the remote host being unaccessible.

If this error is the result of an attempt to read a USENET News group,

the group may not exist.

Check the Message Box for a specific error.

wattcp.cfg再配置上nameserver的ip地址
比如：
nameserver=192.168.0.1

Microsoft DOS TCP/IP Protocol Driver 1.0a
Copyright (c) Microsoft Corporation, 1991. All rights reserved.
Copyright (c) Hewlett-Packard Corporation, 1985-1991. All rights reserved.
Copyright (c) 3Com Corporation, 1985-1991. All rights reserved.
Microsoft DOS TCP/IP NEMM Driver 1.0
MAC/DIS to Packet Driver converter loaded. Version 1.07
Copyright 1991 FTP Software, Inc. All rights reserved.
v1.07 by Joe R. Doupnik, jrd@cc.usu.edu, Utah State Univ, 18 May 1991
The command completed successfully.
Killer v1.0 Copyright 1995 Vincent Penquerc'h. All Rights Reserved.
Killer installed in memory.
DOSKEY installed.
DOSLFN 0.32o: high loaded consuming 11840 bytes.

CuteMouse v1.9.1
Installed at PS/2 port

Now you are in MS-DOS 7.10 prompt. Type 'HELP' for help.

MS-DOS LAN Manager v2.1 Netbind
Performing Power-Up Autosense...
Switching between 10BaseT and 100BaseTx...
Selected media: 100BaseTx (TP 100) Autosense
Microsoft DOS TCP/IP 1.0a

好的，wattcp.cfg配置上nameserver的ip地址，我用192.168.0.1和DNS 服务器地址试试，怎么FTP也启动了，是不是要用BYE才行。

FTP> cd 22712261
250 Directory changed to /22712261
FTP> get key_1985.txt
200 PORT Command successful.
150 Opening ASCII mode data connection for key_1985.txt (47 Bytes).
WATTCP socket error: -1
425 Cannot open data connection.
Transfer of 0 Kbytes (0 bytes) in 26034.95 seconds ( 0.00 Kbytes/s ).

还是不行，是不是ASCII 方式问题