Newbie question: how to install DOS 7.10 under 2000 - China DOS Union Forum

Download the installation file, run it, ok!

That's it?
Where do I download it?

At first glance I thought it was Roy. Where to download it? Right here on this forum, look around slowly.

I thought it was Roy too... You can download it here too:

http://newdos.yginfo.net/dosart32.htm

I'd like to ask all you experts: how do I install DOS 7.10 under WIN2000?
I installed it before, and I remember I downloaded the installation file from the forum too, but now I've forgotten again.
Please give me a hand!

Download the installation file and run it, ok.
How exactly do you run it?
After extracting it, where do you put it and run it from?

Same question!!
Urgent, I need to make a DOS program in a hurry.

I ran it, and it can be installed, but can it set up some kind of dual boot thing!
Can it switch from within WINDOWS?

The specific method is:
First use the SYS command (for example SYS C

to transfer the DOS system files to drive C
Then save the information in the master boot sector at this time
(that is, the DOS boot information) to the file C:\BOOTSECT.DOS. This can easily be done with a small tool called SRC
Tools in this site's "Disk Tools".
Among them, SRCBOOT, SRCMBR, and SRCFAT are commands for saving, backing up, and comparing BOOT, MBR, and
FAT respectively. The specific usage of the SRCTools collection can be found in a special article in the "DOS
Articles" section. For example, SRCBOOT C: C:\BOOTSECT.DOS
/S will save the boot sector of drive C to the file C:\BOOTSECT.DOS. At this point the BOOTSECT.DOS file has been
successfully created. Next is to restore the WinNT/2K/XP boot information, which can be done with the BOOTPART tool
mentioned above, such as BOOTPART WINNT BOOT:C:. Then you only need to modify the BOOT.INI file as described below.

I can't understand it. I don't know anything about boot sectors or boot information!
Can you explain it in less technical terms? Be more specific.

Watch carefully during installation. It can automatically create a dual-boot menu.

For details please look here:
http://newdos.yginfo.net/dosart32.htm

Floor1　iceman9000	Posted 2003-11-05 00:00
初级用户　Posts 5　Credits 120
I'd like to ask all you experts: how do I install DOS 7.10 under WIN2000? I installed it before, and I remember I downloaded the installation file from the forum too, but now I've forgotten again. Please give me a hand!

Floor2　hunome	Posted 2003-11-05 00:00
银牌会员　Posts 721　Credits 2,265
Download the installation file, run it, ok!

Floor3　etb32	Posted 2003-11-21 00:00
初级用户　Posts 7　Credits 134
That's it? Where do I download it?

Floor4　hunome	Posted 2003-11-21 00:00
银牌会员　Posts 721　Credits 2,265
At first glance I thought it was Roy. Where to download it? Right here on this forum, look around slowly.

Floor5　Wengier	Posted 2003-11-21 00:00
系统支持　Posts 10,521　Credits 27,736
I thought it was Roy too... You can download it here too: http://newdos.yginfo.net/dosart32.htm

Floor6　beancurd	Posted 2003-12-06 00:00
初级用户　Posts 5　Credits 117
I'd like to ask all you experts: how do I install DOS 7.10 under WIN2000? I installed it before, and I remember I downloaded the installation file from the forum too, but now I've forgotten again. Please give me a hand! Download the installation file and run it, ok. How exactly do you run it? After extracting it, where do you put it and run it from?

Floor7　medalas	Posted 2003-12-06 00:00
初级用户　Posts 21　Credits 189
Same question!! Urgent, I need to make a DOS program in a hurry.

Floor8　medalas	Posted 2003-12-06 00:00
初级用户　Posts 21　Credits 189
I ran it, and it can be installed, but can it set up some kind of dual boot thing! Can it switch from within WINDOWS?

Floor9　medalas	Posted 2003-12-06 00:00
初级用户　Posts 21　Credits 189
The specific method is: First use the SYS command (for example SYS C to transfer the DOS system files to drive C Then save the information in the master boot sector at this time (that is, the DOS boot information) to the file C:\BOOTSECT.DOS. This can easily be done with a small tool called SRC Tools in this site's "Disk Tools". Among them, SRCBOOT, SRCMBR, and SRCFAT are commands for saving, backing up, and comparing BOOT, MBR, and FAT respectively. The specific usage of the SRCTools collection can be found in a special article in the "DOS Articles" section. For example, SRCBOOT C: C:\BOOTSECT.DOS /S will save the boot sector of drive C to the file C:\BOOTSECT.DOS. At this point the BOOTSECT.DOS file has been successfully created. Next is to restore the WinNT/2K/XP boot information, which can be done with the BOOTPART tool mentioned above, such as BOOTPART WINNT BOOT:C:. Then you only need to modify the BOOT.INI file as described below. I can't understand it. I don't know anything about boot sectors or boot information! Can you explain it in less technical terms? Be more specific.

Floor10　hunome	Posted 2003-12-06 00:00
银牌会员　Posts 721　Credits 2,265
Watch carefully during installation. It can automatically create a dual-boot menu.

Floor11　Wengier	Posted 2003-12-07 00:00
系统支持　Posts 10,521　Credits 27,736
For details please look here: http://newdos.yginfo.net/dosart32.htm