How to install Windows 2000 on the new blue G6000 notebook computer without a CD-ROM or floppy drive? - China DOS Union Forum

Dear all, I have a notebook computer, which is the New Blue G6000 model, without a CD-ROM or floppy drive, with a USB2.0 interface, and supports USB floppy drive boot. I once used the built-in optical engraving combined with an external USB2.0 hard disk as an external CD-ROM to install WINXP, which could be installed normally. However, after formatting the hard disk and using the above CD-ROM to install WIN2000, after the file copying is completed, it restarts and a blue screen appears, showing a hardware error. Then, when using the EKE external CD-ROM to install WIN2000, it cannot be directly booted from the CD, and when booted from the external floppy drive, it often cannot find the CD-ROM. I have also used the method of copying the I386 files under WIN2000 to the hard disk and then restarting to DOS for installation, but it also has a blue screen after copying the installation files. Please tell me how to solve the above problems, thank you for your advice. The notebook configuration is P4-M2.2G, 256M DDR, 40G hard disk, SIS650 chipset, integrated graphics card, network card, modem, and with a GPRS module.

Floor1　lfcjj	Posted 2003-10-10 00:00
初级用户　Posts 1　Credits 107
Dear all, I have a notebook computer, which is the New Blue G6000 model, without a CD-ROM or floppy drive, with a USB2.0 interface, and supports USB floppy drive boot. I once used the built-in optical engraving combined with an external USB2.0 hard disk as an external CD-ROM to install WINXP, which could be installed normally. However, after formatting the hard disk and using the above CD-ROM to install WIN2000, after the file copying is completed, it restarts and a blue screen appears, showing a hardware error. Then, when using the EKE external CD-ROM to install WIN2000, it cannot be directly booted from the CD, and when booted from the external floppy drive, it often cannot find the CD-ROM. I have also used the method of copying the I386 files under WIN2000 to the hard disk and then restarting to DOS for installation, but it also has a blue screen after copying the installation files. Please tell me how to solve the above problems, thank you for your advice. The notebook configuration is P4-M2.2G, 256M DDR, 40G hard disk, SIS650 chipset, integrated graphics card, network card, modem, and with a GPRS module.

Floor2　电吉入侵	Posted 2003-10-11 00:00
初级用户　Posts 377　Credits 1,480
Copy Win2000 to the hard drive, then boot from a USB floppy drive \| CD-ROM to install.

Floor3　doscommand	Posted 2004-03-10 00:00
银牌会员　Posts 148　Credits 1,141
Just install an external CD drive and it's done.

Floor4　枯井无波	Posted 2004-03-10 00:00
初级用户　Posts 10　Credits 146
What format did you use to format your hard drive? Is it because the version you're using only supports the NTFS format? That's probably the cause.

Floor5　不得不爱	Posted 2005-10-01 09:38
超级版主　Posts 2,044　Credits 5,310　From 四川南充
Your WIN2000 installation file is incorrect and is corrupted

Floor6　chujiafu	Posted 2005-10-01 20:24
银牌会员　Posts 595　Credits 1,339　From 安徽　宿州
Maybe it's a hardware issue

Floor7　不得不爱	Posted 2005-10-04 09:00
超级版主　Posts 2,044　Credits 5,310　From 四川南充
I also encountered the situation where after the file copying was completed when installing WIN2000, it failed to enter WIN2000 after restarting. Then I bought a better - quality CD and reinstalled WIN2000, and it was fine. You can also give it a try!