加载DOS驱动程序失败 - 中国DOS联盟论坛 - 中国DOS联盟之联合DOS论坛

USB转网卡口（usb---RJ-45 interface）在DOS下加载驱动程序，错误信息
MAC Iint error:could not locate adapter
error loading device driver DM9PCI.dos

error 7306:the driver failed to initialize
DM9PCI.dos was not loaded

error 7321: Network-card drivers failed to load
请各位大哥帮忙看看：其中配置文件内容是

config.sys内容

shell=a:\command.com a:\/e:2048 /p
device=a:\himem.sys /testmem:off
devicehigh=a:\ifshlp.sys
files=35
buffers=35
dos=high,umb
stacks=9,256
lastdrive=z

protocol.ini 内容
[network.setup]
version=0x3110
netcard=ms$DM9PCI,1,MS$DM9PCI,1
transport=ms$nwlink,MS$NWLINK
transport=ms$ndishlp,MS$NDISHLP
lana0=ms$DM9PCI,1,ms$nwlink
lana1=ms$DM9PCI,1,ms$ndishlp

[MS$NWLINK]
FRAME=ETHERNET_802.2
DriverName=nwlink$
BINDINGS=MS$DM9PCI

[protman]
DriverName=PROTMAN$
PRIORITY=MS$NDISHLP

[MS$DM9PCI]
DriverName=DM9PCI$

[MS$NDISHLP]
DriverName=ndishlp$
BINDINGS=MS$DM9PCI

system.ini 内容
[network drivers]
;netcard=e100b.dos
netcard=DM9PCI.dos
transport=ndishlp.sys
devdir=a:
LoadRMDrivers=yes

[Password Lists]
*Shares=a:\Shares.PWL
TESTER=a:\TESTER.PWL

[network]
sizworkbuf=1498
filesharing=no
printsharing=no
autologon=no
lanroot=a:
username=TESTER
workgroup=WORKGROUP
reconnect=yes
dospophotkey=N
lmlogon=0
logondomain=WORKGROUP
preferredredir=full
autostart=full
maxconnections=8

连接文件内容为
PROMPT $p$g

net initialize
if errorlevel 1 goto linkfail

nwlink
if errorlevel 1 goto linkfail

net start
if errorlevel 1 goto linkfail

net logon bekins bekind2 /yes /savepw:no
if errorlevel 1 goto linkfail

cmdelay 5
net use m: /delete
:start
cmdelay 3
net use m: \\computer\monitor < a:\y.key
if not errorlevel 1 goto end
cmdelay 5
net use m: \\computer\monitor < a:\y.key
if errorlevel 1 goto start
goto end

:linkfail
ECHO LAN link fail > %EXDRV%\err.log

:end

各位大哥看看那个地方配置不对，请指教。

第1楼　jia332	发表于 2008-03-04 15:48
初级用户　发帖 81　积分 160
加载DOS驱动程序失败 USB转网卡口（usb---RJ-45 interface）在DOS下加载驱动程序，错误信息 MAC Iint error:could not locate adapter error loading device driver DM9PCI.dos error 7306:the driver failed to initialize DM9PCI.dos was not loaded error 7321: Network-card drivers failed to load 请各位大哥帮忙看看：其中配置文件内容是 config.sys内容 shell=a:\command.com a:\/e:2048 /p device=a:\himem.sys /testmem:off devicehigh=a:\ifshlp.sys files=35 buffers=35 dos=high,umb stacks=9,256 lastdrive=z protocol.ini 内容 [network.setup] version=0x3110 netcard=ms$DM9PCI,1,MS$DM9PCI,1 transport=ms$nwlink,MS$NWLINK transport=ms$ndishlp,MS$NDISHLP lana0=ms$DM9PCI,1,ms$nwlink lana1=ms$DM9PCI,1,ms$ndishlp [MS$NWLINK] FRAME=ETHERNET_802.2 DriverName=nwlink$ BINDINGS=MS$DM9PCI [protman] DriverName=PROTMAN$ PRIORITY=MS$NDISHLP [MS$DM9PCI] DriverName=DM9PCI$ [MS$NDISHLP] DriverName=ndishlp$ BINDINGS=MS$DM9PCI system.ini 内容 [network drivers] ;netcard=e100b.dos netcard=DM9PCI.dos transport=ndishlp.sys devdir=a: LoadRMDrivers=yes [Password Lists] *Shares=a:\Shares.PWL TESTER=a:\TESTER.PWL [network] sizworkbuf=1498 filesharing=no printsharing=no autologon=no lanroot=a: username=TESTER workgroup=WORKGROUP reconnect=yes dospophotkey=N lmlogon=0 logondomain=WORKGROUP preferredredir=full autostart=full maxconnections=8 连接文件内容为 PROMPT $p$g net initialize if errorlevel 1 goto linkfail nwlink if errorlevel 1 goto linkfail net start if errorlevel 1 goto linkfail net logon bekins bekind2 /yes /savepw:no if errorlevel 1 goto linkfail cmdelay 5 net use m: /delete :start cmdelay 3 net use m: \\computer\monitor < a:\y.key if not errorlevel 1 goto end cmdelay 5 net use m: \\computer\monitor < a:\y.key if errorlevel 1 goto start goto end :linkfail ECHO LAN link fail > %EXDRV%\err.log :end 各位大哥看看那个地方配置不对，请指教。

第2楼　jia332	发表于 2008-03-08 10:14
初级用户　发帖 81　积分 160
顶，请高手指教小弟，如何在DOS下加载驱动实现网络互联