有人能帮忙吗?我需要autoexec.nt... - 中国DOS联盟论坛

Re fenian11:

这是我的autoexec.nt，大部分都是注释行，起作用的只有5行。你可以试试。


@echo off

REM AUTOEXEC.BAT is not used to initialize the MS-DOS environment.
REM AUTOEXEC.NT is used to initialize the MS-DOS environment unless a
REM different startup file is specified in an application's PIF.

REM Install CD ROM extensions
lh %SystemRoot%\system32\mscdexnt.exe

REM Install network redirector (load before dosx.exe)
lh %SystemRoot%\system32\redir

REM Install DPMI support
lh %SystemRoot%\system32\dosx

REM The following line enables Sound Blaster 2.0 support on NTVDM.
REM The command for setting the BLASTER environment is as follows:
REM    SET BLASTER=A220 I5 D1 P330
REM    where:
REM        A    specifies the sound blaster's base I/O port
REM        I    specifies the interrupt request line
REM        D    specifies the 8-bit DMA channel
REM        P    specifies the MPU-401 base I/O port
REM        T    specifies the type of sound blaster card
REM                 1 - Sound Blaster 1.5
REM                 2 - Sound Blaster Pro I
REM                 3 - Sound Blaster 2.0
REM                 4 - Sound Blaster Pro II
REM                 6 - SOund Blaster 16/AWE 32/32/64
REM
REM    The default value is A220 I5 D1 T3 and P330.  If any of the switches is
REM    left unspecified, the default value will be used. (NOTE, since all the
REM    ports are virtualized, the information provided here does not have to
REM    match the real hardware setting.)  NTVDM supports Sound Blaster 2.0 only.
REM    The T switch must be set to 3, if specified.
SET BLASTER=A220 I5 D1 P330 T3

REM To disable the sound blaster 2.0 support on NTVDM, specify an invalid
REM SB base I/O port address.  For example:
REM    SET BLASTER=A0

第1楼　fenian11	发表于 2005-10-05 21:51
新手上路　发帖 1　积分 3
有人能帮忙吗?我需要autoexec.nt... -.-偶潜水多年......想必也玩了N多游戏了... 竟然遇上麻烦了-.-~ 今天下午刚开始玩猫狗2~破解的不错 -.-玩了N小时后.... 天地劫-神魔至尊传100%下好了 -.-Daemon载入... 竟然........ 求各位帮忙..... 自动安装不能...跳出来个框具体内容: 标题:16位WINDOWS子系统内容:F:\windows\system32\autoexec.nt 系统文件不适用于运行MS-DOS与MICrosoft Windows应用程序...选择"关闭"终止应用程序. 两个按钮:关闭.....忽略点了都没反应去system32看看...没这个东东能试的都试了..... -.- 额...... 求各位达人帮忙了...... 附件 asdf.JPG (17.77 KiB)

第2楼　chzhlh	发表于 2005-10-06 04:00
初级用户　发帖 8　积分 154
该文件从XP光盘的I386文件夹中提取就行了

第3楼　JonePeng	发表于 2005-10-06 12:26
金牌会员　发帖 1,883　积分 4,562　来自广东广州
运行CMD，放入XP安装盘，假设光驱盘符是G:，则运行以下命令： expand g:\i386\autoexec.nt_ %SystemRoot%\system32\autoexec.nt expand g:\i386\config.nt_ %SystemRoot%\system32\config.nt

第4楼　willsort	发表于 2005-10-06 15:40
元老会员　发帖 1,512　积分 4,432
Re fenian11: 这是我的autoexec.nt，大部分都是注释行，起作用的只有5行。你可以试试。 @echo off REM AUTOEXEC.BAT is not used to initialize the MS-DOS environment. REM AUTOEXEC.NT is used to initialize the MS-DOS environment unless a REM different startup file is specified in an application's PIF. REM Install CD ROM extensions lh %SystemRoot%\system32\mscdexnt.exe REM Install network redirector (load before dosx.exe) lh %SystemRoot%\system32\redir REM Install DPMI support lh %SystemRoot%\system32\dosx REM The following line enables Sound Blaster 2.0 support on NTVDM. REM The command for setting the BLASTER environment is as follows: REM SET BLASTER=A220 I5 D1 P330 REM where: REM A specifies the sound blaster's base I/O port REM I specifies the interrupt request line REM D specifies the 8-bit DMA channel REM P specifies the MPU-401 base I/O port REM T specifies the type of sound blaster card REM 1 - Sound Blaster 1.5 REM 2 - Sound Blaster Pro I REM 3 - Sound Blaster 2.0 REM 4 - Sound Blaster Pro II REM 6 - SOund Blaster 16/AWE 32/32/64 REM REM The default value is A220 I5 D1 T3 and P330. If any of the switches is REM left unspecified, the default value will be used. (NOTE, since all the REM ports are virtualized, the information provided here does not have to REM match the real hardware setting.) NTVDM supports Sound Blaster 2.0 only. REM The T switch must be set to 3, if specified. SET BLASTER=A220 I5 D1 P330 T3 REM To disable the sound blaster 2.0 support on NTVDM, specify an invalid REM SB base I/O port address. For example: REM SET BLASTER=A0