|
FreeBuilder
初级用户
积分 33
发帖 11
注册 2006-1-30
状态 离线
|
『楼 主』:
[已确定原因]安装DOS7.1后，Win98不正常了
使用 LLM 解释/回答一下
安装 DOS7.1 后，Win98不正常了。
一台586机，Win98安装在逻辑分区，无其它系统。
安装 DOS 7.1 后，启动 DOS7.1 正常，但键入 win 命令进入 98 后，98 老提示访问注册表出现问题，重启修复注册表。
重启，键入 win 启动 98，修复注册表。
重启，键入 Win 启动 98，有提示访问注册表出现问题，要重启修复。
如此循环，直到把 autoexec.bat 和 config.sys 删掉（先备份过）后，Win98 才恢复正常。
究竟是什么原因，小弟在此请教给位大哥，请指教。谢谢！
After installing DOS 7.1, Win98 is abnormal.
A 586 machine, Win98 is installed in a logical partition, and there is no other system.
After installing DOS 7.1, starting DOS 7.1 is normal, but after typing the win command to enter 98, 98 always prompts that there is a problem accessing the registry, and restarts to repair the registry.
Restart, type win to start 98, repair the registry.
Restart, type Win to start 98, there is a prompt that there is a problem accessing the registry, and it needs to be restarted to repair.
This cycle continues until autoexec.bat and config.sys are deleted (after being backed up), and then Win98 returns to normal.
What is the reason exactly? Little brother is asking for advice from big brothers here, please give guidance. Thank you!
|
|
 2006-2-10 13:22 |
|
|
Jneny
高级用户
中國DOS聯盟常任參議员
积分 686
发帖 318
注册 2005-11-4
状态 离线
|
『第 2 楼』:
使用 LLM 解释/回答一下
那先安装WIN98再装MSDOS7。10 呀
Then install WIN98 first and then install MSDOS7.10.
|
|
|
2006-2-10 13:45 |
|
|
JonePeng
金牌会员
Ｄ◎＄ Ｆαп
积分 4562
发帖 1883
注册 2004-1-19
来自 广东广州
状态 离线
|
『第 3 楼』:
使用 LLM 解释/回答一下
唉，Win98本身就是DOS 7.1，没必要再另外安装DOS 7.1了。。。
Alas, Win98 itself is DOS 7.1, there's no need to install DOS 7.1 separately...
|
－－－－＝＝＝＝≡≡≡≡ 我的至爱，永远是MSDOS！≡≡≡≡＝＝＝＝－－－－
 |
|
|
2006-2-10 14:48 |
|
|
1468699
初级用户
积分 152
发帖 10
注册 2004-5-17
状态 离线
|
『第 4 楼』:
使用 LLM 解释/回答一下
其实DOS7.1就是从98中分离出来的。如装上两个，就像你要装两个WIN98一样。如果装了WIN98后还想再装DOS7.1。
最好是用多系统管理软件。
这是我惨痛的经验。(因我在格式化与安装之间来回了-----直到光驱都快坏了)
Actually, DOS 7.1 is separated from Windows 98. If you install two, it's like you want to install two Windows 98s. If you want to install DOS 7.1 after installing Windows 98, it's best to use a multi - system management software. This is my painful experience. (Because I went back and forth between formatting and installing ----- until the CD - ROM was almost broken)
|
|
|
2006-2-10 21:54 |
|
|
yuren008
初级用户
积分 72
发帖 30
注册 2005-11-16
来自 中国
状态 离线
|
『第 5 楼』:
使用 LLM 解释/回答一下
怎么回是这样呢？那DOS7.1要和什么系统安装呢？
Why is it like this? Then what system should DOS 7.1 be installed with?
|
|
|
2006-2-10 23:12 |
|
|
FreeBuilder
初级用户
积分 33
发帖 11
注册 2006-1-30
状态 离线
|
『第 6 楼』:
使用 LLM 解释/回答一下
我把 IO.SYS COMMAND.COM 删掉，用 Win98启动盘启动，sys c:，并恢复MSDOS.SYS，只要原来的config.sys 在，Win98就不正常，我知道肯定是 config.sys 里加载的某个驱动有问题，但我就是想不通也查不出具体是哪个的问题。
补充：我另外安装DOS7.1是因为我想像DOS6那样通过config.sys和autoexec.bat配置多选项启动，以及可以更改启动画面，98的启动画面在IO.SYS里面。
I deleted IO.SYS COMMAND.COM, booted with a Win98 boot disk, ran sys c:, and restored MSDOS.SYS. But if the original config.sys is present, Win98 doesn't work properly. I know there's a driver loaded in config.sys that's causing the problem, but I just can't figure out which one it is.
Supplement: I installed DOS7.1 additionally because I want to configure multi-option startup through config.sys and autoexec.bat like in DOS6, and also change the boot screen. The boot screen of 98 is in IO.SYS.
|
|
|
2006-2-12 02:21 |
|
|
Wengier
系统支持
“新DOS时代”站长
积分 27736
发帖 10521
注册 2002-10-9
状态 离线
|
『第 7 楼』:
使用 LLM 解释/回答一下
这个问题我经反复试图重现你的情况后现在已正式确认了原因：并非CONFIG.SYS中的某个驱动有问题，而是你安装DOS 7.1时的代码页未选择正确！既然你是安装的中文版的Win98，安装DOS时也应相应选择简体中文代码页（936），而非其它代码页，否则启动中文版的Win98时必将出现这种错误！经验证，只要所选的DOS代码页与Win98所用代码页相同，就不会出现这种问题。
I have repeatedly tried to reproduce your situation, and now I officially confirm the cause: it's not that there's a problem with a certain driver in CONFIG.SYS, but that the code page when you installed DOS 7.1 was not selected correctly! Since you are installing the Chinese version of Win98, when installing DOS, you should also select the Simplified Chinese code page (936) accordingly, not other code pages. Otherwise, this kind of error will definitely occur when starting the Chinese version of Win98! It has been verified that as long as the selected DOS code page is the same as the code page used by Win98, this problem will not occur.
|
Wengier - 新DOS时代
欢迎大家来到我的“新DOS时代”网站，里面有各类DOS软件和资料，地址：
http://wendos.mycool.net/
E-Mail & MSN: wengierwu AT hotmail.com （最近比较忙，有事请联系DOSroot和雨露，谢谢！）
 |
|
|
2006-6-30 04:41 |
|
|
不得不爱
超级版主
我爱DOS
积分 5310
发帖 2044
注册 2005-9-26
来自 四川南充
状态 离线
|
|
|
2006-6-30 08:25 |
|
|
不得不爱
超级版主
我爱DOS
积分 5310
发帖 2044
注册 2005-9-26
来自 四川南充
状态 离线
|
|
|
2006-6-30 08:27 |
|
|
不得不爱
超级版主
我爱DOS
积分 5310
发帖 2044
注册 2005-9-26
来自 四川南充
状态 离线
|
|
|
2006-6-30 08:28 |
|
|
Wengier
系统支持
“新DOS时代”站长
积分 27736
发帖 10521
注册 2002-10-9
状态 离线
|
『第 11 楼』:
使用 LLM 解释/回答一下
qwe1234567：楼主这个问题确实是DOS代码页的原因，不是路径的原因！我已经测试确定，绝对没错。如果路径有误的话则是另外的情况，具体我以前已经提过（早在以前做超级DOS启动盘时就讨论过），故在此不再重复。
qwe1234567: The problem of the landlord is indeed due to the DOS code page, not the path! I have tested and confirmed that it is absolutely correct. If the path is incorrect, it is another situation. Specifically, I have mentioned it before (it was discussed when making the super DOS boot disk a long time ago), so I won't repeat it here.
|
Wengier - 新DOS时代
欢迎大家来到我的“新DOS时代”网站，里面有各类DOS软件和资料，地址：
http://wendos.mycool.net/
E-Mail & MSN: wengierwu AT hotmail.com （最近比较忙，有事请联系DOSroot和雨露，谢谢！）
|
|
|
2006-6-30 11:33 |
|
