|
jimian
新手上路

积分 14
发帖 8
注册 2011-1-3
状态 离线
|
『楼 主』:
请教NTFS1.1 1.2一题
使用 LLM 解释/回答一下
题一:
当把NTFS3.5系统盘作为从盘接入XP系统后,会被升级为NTFS3.1,从而导致该从盘的NTFS3.5不能被引导。请问有什么办法避免自动升级,又或者,能有软件能无损转换回1.2或1.1版本?
(此前发生过一次这样的问题,一块3.5的硬盘接到一台标准安装的xp sp2上,再取下后,就不能启动了,查看ntfs版本,发现变成3.1乐)
请各位先生多多指教,多谢了!
Question 1:
When the NTFS 3.5 system disk is connected as a slave disk to the XP system, it will be upgraded to NTFS 3.1, resulting in the fact that the NTFS 3.5 on this slave disk cannot be booted. Is there any way to avoid automatic upgrade, or is there any software that can无损convert it back to version 1.2 or 1.1?
(This problem occurred once before. A 3.5 - inch hard disk was connected to a standard - installed XP SP2, and then when it was removed, it could not start. Checking the NTFS version, it was found that it had become 3.1)
Please give your advice, thank you very much!
|
|
2011-1-4 21:01 |
|
|
xkai2010
初级用户
 
积分 121
发帖 57
注册 2010-8-9
状态 离线
|
『第 2 楼』:
使用 LLM 解释/回答一下
用NT4.0的安装光盘启动系统,找到那个被升级的分区(此时肯定是无法识别的),将其“转换为NTFS”试试
Boot the system with the installation CD of NT4.0, find the partition that was upgraded (it must be unrecognized at this time), and try to "convert it to NTFS"
|
|
2011-1-5 11:18 |
|
|
Roy
管理员
          專業島民
积分 4869
发帖 1633
注册 2002-12-10
状态 离线
|
|
2011-1-5 11:52 |
|
|
jimian
新手上路

积分 14
发帖 8
注册 2011-1-3
状态 离线
|
『第 4 楼』:
使用 LLM 解释/回答一下
多谢两位!
TO xkai2010: 记得安装过程中的转换过程是格式化吧...那就没用了,不过还不确定。
另外,其实我还在下NT系统,就是那个all in one版本的,太慢了,两天了还没下完,也不知道最终是不是可以顺利下完(所说的NT系统都是原先机器上就有的)
TO ROY: 下了winpm7,看到里面的转换版本功能了,可以在3.1和1.2直接转换。等系统下载完成了安装后实际测试效果。再问:3.0 3.1可以认为是兼容的,那么1.1和1.2也是兼容了?
另外,还是想知道,能避免高版本NTFS的系统会对接入的从盘自动升级吗?不然每次都这样转换太麻烦了
Thanks to both of you!
TO xkai2010: Remember that the conversion process during installation is formatting... Then it's useless, but I'm not sure yet.
Also, actually I'm still downloading the NT system, that is the all in one version, it's too slow, it hasn't been downloaded in two days, and I don't know if it will be successfully downloaded in the end (the so-called NT systems are all the ones that were originally on the machine)
TO ROY: I downloaded winpm7 and saw the conversion version function in it, which can convert directly between 3.1 and 1.2. Wait until the system is downloaded and installed to test the effect actually. Then ask: 3.0 and 3.1 can be considered compatible, so are 1.1 and 1.2 compatible?
Also, I still want to know, can the system with a high version of NTFS avoid automatically upgrading the connected slave drive? Otherwise, it's too troublesome to convert every time
|
|
2011-1-5 22:53 |
|
|
fujianabc
金牌会员
     
积分 3467
发帖 1616
注册 2004-6-21
状态 离线
|
『第 5 楼』:
使用 LLM 解释/回答一下
1.1和1.2貌似应该是不兼容的
1.1 and 1.2 seem to be incompatible
|
|
2011-1-7 10:45 |
|