中国DOS联盟

最近需要编写一个DOS的驱动程序，在看“DOS程序员参考手册”,里面有一个驱动程序的例子，程序如下,但是开机后显示完“Sample Device Driver..Version”，系统就没有反应了，不能返回DOS提示符了，这里有人做过dos驱动的朋友吗，能不能帮我解决这个问题。
; drvr.asm

CR EQU 0Dh
LF EQU 0Ah
MAXCMD EQU 16
ERROR EQU 8000h
BUSY EQU 0200h
DONE EQU 0100h
UNKNOWN EQU 8003h
cseg segment public 'code'
org 0
assume cs : cseg , ds : cseg , es : cseg
; ============================================================
drvr proc far
dD -1
dw 8000h
dw strategy
dw interrupt
db 'Driver01'
; =========================================================
rh_seg dw ?
rh_off dw ?
strategy :
mov cs : rh_seg , es
mov cs : rh_off , bx
ret
; ========================================================
; dispatch table
; ===============================================================
d_tbl:
dw s_init ; Initialization
dw s_mchk ;Media Check
dw s_bpb ;BIOS parameter block
dw s_ird ; IOCTL read
dw s_read ; Read
dw s_nrd ; Nondestructive read
dw s_inst ;Current input status
dw s_infl ;Flush input buffer
dw s_write ;Write
dw s_vwrite ;Write with verify
dw s_ostat ;Current output status
dw s_oflush ;Flush output buffers
dw s_iwrt ; IOCTL write
dw s_open ; open
dw s_close ; Close
dw s_media ; Removable media
dw s_busy;output until busy
; ==============================================================
; interrupt routine
; ==============================================================
interrupt proc far
cld
push es
push ds
push ax
push bx
push cx
push dx
push si
push di
push bp
mov dx,cs: rh_seg
mov es , dx
mov bx,cs: rh_off
mov al,es:[bx]+2
xor ah,ah
cmp ax,MAXCMD
jle ok
mov ax,UNKNOWN
jmp finish
ok:
shl aX,1
mov bx,ax
jmp word ptr[bx+d_tbl]
finish:
mov dx,cs:rh_seg
mov es,dx
mov bx,cs:rh_off
or ax,DONE
mov es:[bx]+3,ax
pop bp
pop di
pop Si
pop dx
pop cx
pop bx
pop ax
pop ds
pop es
iret ;Back to DOS
interrupt endp
;======================================================================================================
; main body of driver
;======================================================================================================
s_mchk: ;Media check
s_bpb: ;BIOS parameter block
S_ird: ;IOCTL read
S_read: ;Read
s_nrd: ;Nondestructive read
s_inst: ;Current input status
s_infl: ;Flush input buffers
S_vwrite: ;Current output status
S_ostat: ;Current Output Status
s_oflush: ;Flush output buffers
S_iwrt: ;IOCTL write
s_open: ;open
s_close:;Close
s_media:;Removable media
s_busy: ;output until busy
MOV AX, UNKNOWN ;Set error bits
jmp finish
ident:
db CR,LF
db 'Sample Device Driver..Version'
db '0,1'
db CR,LF,LF,'$'
s_init:
mov ah,9 ;Print String
mov dx,offset ident
int 21h
mov dx,CS:rh_seg
mov es,dX
mov bx,CS:rh_off
lea aX,end_driver ;Get end of driver address
mov es:[bX]+14,ax
mov es:[bX]+16,cx
xor aX,ax ;Zero the AX register
jmp finish
s_write:
xor ax,ax
jmp finish
end_driver:
drvr endp
cseg ends
end

请尝尝试下面的任一种方案：
方案1＞将IRET改为RET。
方案2＞将IRET和RET改作RETF。

顶一下。

偶也看了这本书上的程序，里面明明有语言解释说，中断例程不是一个中断，不是以IRet而是以Ret终止！！木是果然厉害。羡慕

1楼的源程序有两处错：
1）如gezi322所说“中断例程不是一个中断”，IRET必须改成RET；
2）“开机后显示完“Sample Device Driver..Version”，系统就没有反应了，不能返回DOS提示符了”：因为加载.SYS时还未进入DOS，DOS中断int 21h是不应该调用的，可改用BIOS中的INT 10h的09h/0ah/0eh/13h功能实现显示。

支持，在交流中成长。

这个驱动的嵌套结构好像有点问题？
interrupt endp,这句是否应该去掉？？