關于 Packet driver 的一個小問題? - 中国DOS联盟论坛

Packet Driver (8139)的名字是：Rtspkt.com

你可能弄错了。

如果需要，请询问我。下面是它的说明

Packet Driver

Introduction:
-------------
This document describes the procedure to setup the Packet driver for
REALTEK RTS8139(A) PCI fast ethernet card.

Location of Driver: \RTSPKT\RTSPKT.COM

Sample Configuration Files:
---------------------------
AUTOEXEC.BAT
RTSPKT 0x60

Notes:
------
1. Load the packet driver using the software interrupt and any
optional switches if required.

Usage: RTSPKT [options] <software_int_no> [media type]

Example: RTSPKT -i 0x7e

The only required parameter is the software interrupt. A packet
driver needs to have a software interrupt assigned to it for other
programs to access it. The recommended interrupt 0x7e. If you need
any of the options listed below, place them before the software
interrupt on the command line.

-i - Force driver to report itself as 802.3 instead of Ethernet II.
-d - Delayed initialization. Used for diskless booting
-n - NetWare conversion. Converts 802.3 packets into 8137 packets
-w - Windows hack, obsoleted by winpkt
-p - Promiscuous mode disable
-h - Help
-u - Uninstall

2. Media type can be used to force the card to work on specific
speed and duplex mode. If no media type if specified, then
driver will read hardware configuration from EEPROM on the
card. The hardware configuration can be modified by running
'rset8139' on driver disk.

3. Type command,C:\RTSPKT 0x60, the screen will appear following
message:

System: [345]86 processor, PCI bus, Two 8259s
Packet driver software interrupt is 0x60
Interrupt number is 0x9
I/O port is 0x6100
My Ethernet address is 52:54:4C:29:29:AD

4. Installing Multiple LAN Adapters:

If there are multiple network cards on the main board. the user
run RTSPKT 0x60 directly, then the screen will display :

Packet driver for RTL8139(A) PCI fast ethernet NIC, version 3.16
Copyright 1999(c), Realtek Semiconductor Inc.

There are 2 network cards on your main board :
Card 1. IRQ= 0x9 I/O= 0x6100 NodeID= 52:54:4C:29:29:AD
Card 2. IRQ= 0xA I/O= 0x6000 NodeID= 52:54:4C:29:29:64
Please select a Card No.(1-2): 1

System: [345]86 processor, PCI bus, Two 8259s
Packet driver software interrupt is 0x60
Interrupt number is 0x9
I/O port is 0x6100
My Ethernet address is 52:54:4C:29:29:AD

5. Installing multiple drivers:

If you want to install multiple cards each connecting to different
network, you have to install the driver multiple times, each with
different packet interrupt number. Then modify 'ioaddr' variable
in 'config.tel' to specify the packet inetrrupt you will use.

---David Tang---

第1楼　himen	发表于 2005-10-25 14:12
新手上路　发帖 2　积分 4
關于 Packet driver 的一個小問題? 最近在做基于DOS和Windows2000的TCP/IP項目﹐但卻找不到RTL8169網卡的Packet driver﹐我在RTL的官方網站找到的是﹕ NDIS2 driver for DOS (Support MSclient,Lantastic,Lanman ) 哪位高手可以告訴我﹐是不是NDIS2的可以轉換成Packet driver或者哪位朋友可以提供一個RTL8169的Packet driver﹐謝謝。

第2楼　Michael	发表于 2005-10-25 18:45
钻石会员　发帖 3,041　积分 10,056
dispkt.dos可以将ndis驱动转换为packet．不过我是安装了ms network client了的．

第3楼　Wengier	发表于 2005-10-26 00:29
系统支持　发帖 10,521　积分 27,736
RTL8169網卡官方網頁上其實是有Packet driver驅動程序的，可惜好像放錯了地方。以前也是查了一陣才發現。

第4楼　himen	发表于 2005-10-26 10:06
新手上路　发帖 2　积分 4
謝謝你們﹐這兩種方式我都試一下看看.

第5楼　JustForYou	发表于 2005-10-26 10:14
新手上路　发帖 8　积分 17
各位大虾,我已经下载了Dis_Pkt.dos,安装完MSCLINT3,并修改了system.ini和protrol.ini,可我重启运行FTP.exe,还是提示:没有找到Packet Driver,请高手们指点!!谢谢!

第6楼　killiori	发表于 2005-10-27 15:02
新手上路　发帖 15　积分 15　来自湖北襄樊
呵呵，其实不用这么麻烦，你买一块RTl8139，其软盘自带。 Packet Driver (8139)的名字是：Rtspkt.com 你可能弄错了。如果需要，请询问我。下面是它的说明 Packet Driver Introduction: ------------- This document describes the procedure to setup the Packet driver for REALTEK RTS8139(A) PCI fast ethernet card. Location of Driver: \RTSPKT\RTSPKT.COM Sample Configuration Files: --------------------------- AUTOEXEC.BAT RTSPKT 0x60 Notes: ------ 1. Load the packet driver using the software interrupt and any optional switches if required. Usage: RTSPKT [options] <software_int_no> [media type] Example: RTSPKT -i 0x7e The only required parameter is the software interrupt. A packet driver needs to have a software interrupt assigned to it for other programs to access it. The recommended interrupt 0x7e. If you need any of the options listed below, place them before the software interrupt on the command line. -i - Force driver to report itself as 802.3 instead of Ethernet II. -d - Delayed initialization. Used for diskless booting -n - NetWare conversion. Converts 802.3 packets into 8137 packets -w - Windows hack, obsoleted by winpkt -p - Promiscuous mode disable -h - Help -u - Uninstall 2. Media type can be used to force the card to work on specific speed and duplex mode. If no media type if specified, then driver will read hardware configuration from EEPROM on the card. The hardware configuration can be modified by running 'rset8139' on driver disk. 3. Type command,C:\RTSPKT 0x60, the screen will appear following message: System: [345]86 processor, PCI bus, Two 8259s Packet driver software interrupt is 0x60 Interrupt number is 0x9 I/O port is 0x6100 My Ethernet address is 52:54:4C:29:29:AD 4. Installing Multiple LAN Adapters: If there are multiple network cards on the main board. the user run RTSPKT 0x60 directly, then the screen will display : Packet driver for RTL8139(A) PCI fast ethernet NIC, version 3.16 Copyright 1999(c), Realtek Semiconductor Inc. There are 2 network cards on your main board : Card 1. IRQ= 0x9 I/O= 0x6100 NodeID= 52:54:4C:29:29:AD Card 2. IRQ= 0xA I/O= 0x6000 NodeID= 52:54:4C:29:29:64 Please select a Card No.(1-2): 1 System: [345]86 processor, PCI bus, Two 8259s Packet driver software interrupt is 0x60 Interrupt number is 0x9 I/O port is 0x6100 My Ethernet address is 52:54:4C:29:29:AD 5. Installing multiple drivers: If you want to install multiple cards each connecting to different network, you have to install the driver multiple times, each with different packet interrupt number. Then modify 'ioaddr' variable in 'config.tel' to specify the packet inetrrupt you will use. ---David Tang---

第7楼　Michael	发表于 2005-10-27 19:02
钻石会员　发帖 3,041　积分 10,056
贴上来你的system.ini和protocol.ini来让大家看看。还有autoexec.bat和config.sys。