点击下载530网卡驱动
说明:
在dos下的用法
530\PKTDRV\DLKFET.com -n 0x60
用法资料英文版
D-Link DFE-530TX PCI Fast Ethernet Adapter Packet Driver
Installation Overview
User's Guide
------------
File Description
------------ ----------------------------------------------------
PCNFS.TXT Sun PC-NFS installation document
PCTCP.TXT FTP PC/TCP installation document
PDIPX.TXT IPX SHELL installation document
NCSA.TXT NCSA installation document
WINSOCK.TXT Winsock installation document
The following syntax keywords are for driver v4.10 or latter only.
-------------------------------------------------------------------
Installation Packet Driver:
----------------------------
1) Copy the Packet driver to your HardDisk, suppose you copy it to
C:\PACKET directory.
EX: copy a:\packet\dlkfet.com c:\packet\dlkfet.com
2) Add the following line to C:\AUTOEXEC.BAT
C:\PACKET\DLKFET -n 0x60
or
1) Copy the Packet driver to your HardDisk, suppose you copy it to
C:\PACKET directory.
EX: copy a:\packet\dlkfet.sys c:\packet\dlkfet.sys
2) Add the following line to C:\CONFIG.SYS
DEVICE=C:\PACKET\DLKFET.SYS -n 0x60
Sample of configuration file:
----------------------------------------------------------------
(Suppose PACKET driver is copied to C:\PACKET directory)
File Name: C:\AUTOEXEC.BAT
----------
C:\PACKET\DLKFET -n -w 0x60
0x60 is software vector number this driver uses.
-n means Novell packets can be transmitted across this driver
-w means Window compatible.
if you want to link to N-way Device and use auto mode, you can add parameter as follow:
C:\PACKET\DLKFET -a -n0x60
if you want to force assigning pci slot number you can add parameter as follow:
C:\PACKET\DLKFET -l10 -n 0x60 (pci slot number=10)
if you want to set up your connection type, you can add parameter as follow:
C:\PACKET\DLKFET -connectiontype=autosense 0x60 (Auto mode, default value)
C:\PACKET\DLKFET -connectiontype=10baset 0x60 (speed=10Mbs, halfduplex)
C:\PACKET\DLKFET -connectiontype=10basetfd 0x60 (speed=10Mbs, fullduplex)
C:\PACKET\DLKFET -connectiontype=100basetx 0x60 (speed=100Mbs, halfduplex)
C:\PACKET\DLKFET -connectiontype=100basetxfd 0x60 (speed=100Mbs, fullduplex)
if you want to set up your flow control ability, you can add parameter as follow:
C:\PACKET\DLKFET -flow_control=hardware_default 0x60 (use hardware value, default)
C:\PACKET\DLKFET -flow_control=enable 0x60 (enable flow control)
C:\PACKET\DLKFET -flow_control=disable 0x60 (disable flow control)
if you want to use installable device driver (dlkfet.sys), you should add these
configuration in CONFIG.SYS and add "DEVICE=" before "C:\PACKET\DLKFET".
The following syntax and keywords are for driver v4.10 previously(v4.10 not included).
--------------------------------------------------------------------------------------
syntax:
DEVICE = DLKFET.SYS
DLKFET.COM
Parameters:
is the software interrupt vector number used by
the packet driver program, which can be from
96 to 128.
Note: can be hex or decimal
number.
hex - start with '0x'.
ex. >DLKFET 0x62
dec - start with nonzero digit.
ex. >DLKFET 98
is the number of assigned slot, which is from 1
to f.
Note: '##' can be hex number only.
ex:>DLKFET /slot=1
>DLKFET /slot=2
>DLKFET /slot=f
Delay Initial - The driver program will not
initialize the network interface card until the
packet driver program is accessed by its upper
layer program first time.
the /w parameter is used only in the Windows
environment.
unload the driver program from memory.
The program will automatically search for Packet
driver to unload.
NetWare conversion
To select media type, you can use :
this is the default setting. It let you be able to
change media without restart the driver.
Force the driver to select 100Mbps full duplex mode.
Force the driver to select 100Mbps half duplex mode.
Force the driver to select 10Mbps full duplex mode.
Force the driver to select 10Mbps half duplex mode.
Set flow_control function.
