中国DOS联盟

vkill LZ, why didn't my experiment succeed?

F:\>smtp.bat
Checking network
Please enter email username: eHljb29yZGluYXRl
Must ensure it's the same username as before base64 encoding
Please enter email username (non-base64 encoded): xycoordinate
Please enter email password: Base64 encoding
Format is xxx@xxx.xxx For example: test@test.com
Please enter recipient: xycoordinate@126.com
Please enter email subject: test
Please enter email body: abcd
Obtaining IP of smtp.163.com
IP obtained
Sending email
(UNKNOWN) 25 (?): connection refused
sent 0, rcvd 0: NOTSOCK
Email sent, press any key to start sending again

Email username and password are both calculated using the "0401" post!!!
http://www.cn-dos.net/forum/viewthread.php?tid=27203&fpage=1&highlight=

Last edited by xycoordinate on 2007-3-17 at 09:59 AM ]

I don't understand, it's so profound~

Master vkill, please take a look: I want to implement the function of receiving Yahoo mail. The operation is as follows:

I entered the following command in the command line:
telnet pop.mail.yahoo.com 110
After a while, it displayed:
+OK hello from popgate on pop102.plus.mail.mud.yahoo.com 2.38.1
Later, no matter what I typed, it displayed the following information:
-ERR popgate unknown command

Originally posted by hello547rf44 at 2007-11-6 19:46:
Master vkill, please see: I want to implement the function of receiving Yahoo emails. The operation is as follows:

I entered the following command in the command line:
telnet pop.mail.yahoo.com 110
After a while, it displayed:
+OK hello from popgate ...

++OK hello from popgate on pop101.plus.mail.mud.yahoo.com 2.38.1
user he200377+OK password required.
pass *****
+OK maildrop ready, 85 messages (627109 octets) (25955179 3758096384)
quit
+OK server signing off.


Lost connection with the host.

C:\>telnet pop.mail.yahoo.com 110
Please make sure your input is correct

Last edited by vkill on 2007-11-6 at 08:01 PM ]

After entering CMD after the command telnet pop.mail.yahoo.com 110, the screen displays +OK hello from popgate on pop103.plus.mail.mud.yahoo.com 2.38.1 and then there is no response. The cursor is still blinking and characters can be entered, but all are -ERR popgate unknown command. The computer seems to slow down suddenly.

Could this is probably related to the fact that I'm using a streamlined version of the system, maybe a certain component has been deleted.

Top! Last edited by hello547rf44 on 2007-11-7 at 09:29 AM ]

It is estimated that it is a problem with your system. It is best not to simplify the system.

After reading this post, I still haven't learned how to send emails with batch processing.

Set cdo = CreateObject("CDO.Message")
strCfg = "http://schemas.microsoft.com/cdo/configuration/"
With cdo
  .Sender = "发送者邮件地址"
  .From = "发送者邮件地址"
  .To = "接收者邮件地址"
  .Fields("urn:schemas:mailheader:X-Priority") = 1 
  .Fields.Update 
  .Subject = "邮件标题"
  .TextBody = "邮件内容"
  .Configuration(strCfg & "SendUsing") = 2
  .Configuration(strCfg & "smtpserver") = "发送邮件服务器地址"
  .Configuration.Fields.Update
  .Send
End With 
msgbox "发送完成"

VBS can:

Set cdo = CreateObject("CDO.Message")
strCfg = "http://schemas.microsoft.com/cdo/configuration/"
With cdo
  .Sender = "Sender's email address"
  .From = "Sender's email address"
  .To = "Recipient's email address"
  .Fields("urn:schemas:mailheader:X-Priority") = 1 
  .Fields.Update 
  .Subject = "Email subject"
  .TextBody = "Email content"
  .Configuration(strCfg & "SendUsing") = 2
  .Configuration(strCfg & "smtpserver") = "SMTP server address for sending"
  .Configuration.Fields.Update
  .Send
End With 
msgbox "Sent successfully"