Question about using GHOST for network backup under DOS! - China DOS Union Forum

I have an IBM T20 laptop. Yesterday I just bought an ITCOM PCMCIA laptop network card, using the RT8319 chip. I followed the desktop method for network GHOST (the desktop can do network GHOST normally):
1. Use GHOST2003 Enterprise Edition to make an MS-DOS network boot disk, with the RT8319 driver included (but it does not support PCMCIA network cards).
2. Since the RT8319 driver included with the boot disk made by GHOST2003 could not properly drive the PCMCIA network card, I modified CONFIG.SYS myself and added DEVICE=\net\RTPCI.exe on the third line.
3. Save and reboot.
Then the problem came. The screen shows DEVICE FOUND and some IRQ interrupt prompts, which indicates the network card driver has already loaded correctly, but when NETBIND.COM loads, an error appears: ERROR 33 UNENABLE BIND. How can this be solved??? Is GHOST poor at supporting PCMCIA network cards, or did I install it wrong?

Originally posted by 中华保镖 at 2003-9-30 00:00:
I have an IBM T20 laptop. Yesterday I just bought an ITCOM PCMCIA laptop network card, using the RT8319 chip. I followed the desktop method for network GHOST (the desktop can do network GHOST normally):
...

I've run into the same kind of problem too, urgent, waiting for an expert to solve it!

Download the driver for the 8139 network card from the Realtek website: ftp://152.104.238.194/cn/nic/rtl8139abcd8130810xseries/cboem-8139(130).zip

After extracting it, copy these three files from the rtsoemcb.130\exe\RTSPKT directory: RtBios.com, RtPci.exe, and RtsPkt.com to the boot disk.
Make sure there is no Device=Emm386.exe NoEms command in the Config.sys file on the boot disk.
The commands for loading the network card driver and starting Ghost are as follows:

RtPci /md000 /i11
RtBios
RtsPkt 0x60
Ghost

[ Last edited by LanCat on 2006-8-15 at 04:22 ]

Floor1　中华保镖	Posted 2003-09-30 00:00
初级用户　Posts 3　Credits 112
I have an IBM T20 laptop. Yesterday I just bought an ITCOM PCMCIA laptop network card, using the RT8319 chip. I followed the desktop method for network GHOST (the desktop can do network GHOST normally): 1. Use GHOST2003 Enterprise Edition to make an MS-DOS network boot disk, with the RT8319 driver included (but it does not support PCMCIA network cards). 2. Since the RT8319 driver included with the boot disk made by GHOST2003 could not properly drive the PCMCIA network card, I modified CONFIG.SYS myself and added DEVICE=\net\RTPCI.exe on the third line. 3. Save and reboot. Then the problem came. The screen shows DEVICE FOUND and some IRQ interrupt prompts, which indicates the network card driver has already loaded correctly, but when NETBIND.COM loads, an error appears: ERROR 33 UNENABLE BIND. How can this be solved??? Is GHOST poor at supporting PCMCIA network cards, or did I install it wrong?

Floor2　vagrancyliu	Posted 2006-08-14 17:45
初级用户　Posts 8　Credits 39　From 广东东莞
Originally posted by 中华保镖 at 2003-9-30 00:00: I have an IBM T20 laptop. Yesterday I just bought an ITCOM PCMCIA laptop network card, using the RT8319 chip. I followed the desktop method for network GHOST (the desktop can do network GHOST normally): ... I've run into the same kind of problem too, urgent, waiting for an expert to solve it!

Floor3　LanCat	Posted 2006-08-15 03:51
中级用户　Posts 78　Credits 288
Download the driver for the 8139 network card from the Realtek website: ftp://152.104.238.194/cn/nic/rtl8139abcd8130810xseries/cboem-8139(130).zip After extracting it, copy these three files from the rtsoemcb.130\exe\RTSPKT directory: RtBios.com, RtPci.exe, and RtsPkt.com to the boot disk. Make sure there is no Device=Emm386.exe NoEms command in the Config.sys file on the boot disk. The commands for loading the network card driver and starting Ghost are as follows: RtPci /md000 /i11 RtBios RtsPkt 0x60 Ghost [ Last edited by LanCat on 2006-8-15 at 04:22 ]