VMware Network Configuration - China DOS Union Forum - China DOS Union

Thanks, the source address couldn't be downloaded. Later, I found it in that post. There's another question I want to ask you. When the FTP runs, it prompts "no packet driver found", which should be that the network card driver isn't found. I'm using VMware to install DOS, installed MSClient, and the network card installed is VMware's pcntnd.dos. So I followed the instructions in the wattcp manual to try, but many problems occurred again. I don't know how to solve it. I tried many configuration methods but couldn't get it to work. The following is my own configuration file. I hope you can help see where the problem is. Thanks!

Config.sys configuration:
DEVICE=C:\DOS71\ECHO.SYS W/e/l/c/o/m/e /t/o MS-DOS 7.10...
DEVICE=C:\DOS71\ECHO.SYS C/o/p/y/r/i/g/h/t M/i/c/r/o/s/o/f/t C/o/r/p. A/l/l /r/i/g/h/t/s /r/e/s/e/r/v/e/d.
DEVICE=C:\DOS71\HIMEM.SYS/testmem:off
DEVICE=C:\DOS71\EMM386.EXE noems novcpi
DEVICEHIGH=C:\DOS71\SETVER.EXE
REM DEVICEHIGH=C:\DOS71\POWER.EXE
DEVICEHIGH=C:\DOS71\VIDE-CDD.SYS /D:IDE-CD
REM DEVICEHIGH=C:\DOS71\DISPLAY.SYS CON=(,,1)
COUNTRY=001,437,C:\DOS71\COUNTRY.SYS
SHELL=COMMAND.COM /P /E:640
DOS=HIGH,UMB,AUTO
FCBS=4,0
FILES=30
BUFFERS=15,0
LASTDRIVE=J
STACKS=9,256
SET PATH=C:\DOS71;..;C:\MASM5.0;.\net
device=C:\NET\ifshlp.sys
devicehigh=c:\net\protman.dos /i:c:\net
devicehigh=c:\net\dis_pkt.dos
devicehigh=c:\net\pcntnd.dos
devicehigh=c:\net\nemm.dos

Autoexec.bat configuration:
C:\NET\net initialize
@ECHO OFF
PROMPT $P$G
SET DIRCMD=/4
MODE CON RATE=32 DELAY=1
REM MODE CON CP PREPARE=((437)EGA.CPI)
REM MODE CON CP SELECT=437
REM KEYB US,,KEYBOARD.SYS
LH KILLER
LH DOSKEY
LH DOSLFN /Z:C:\DOS71\CP437UNI.TBL
REM LH MSCDEX /D:IDE-CD
LH SHARE /L:30
REM LH NLSFUNC
LH SMARTDRV
REM LH CTMOUSE
REM For compatiblity purpose:
LH CTMOUSE > NUL
ECHO.
REM For locking volumes to enable "direct disk access":
CALL LOCKDRV.BAT
BREAK ON
LFNFOR ON
ECHO Now you are in MS-DOS 7.10 prompt. Type 'HELP' for help.
ECHO.
SET CTSYN=C:\SOUND
SET MIDI=SYNTH:1 MAP:E MODE:0
SET BLASTER=A220 I5 D1 H5 P330 E620 T6
PATH=C:\NET;C:\DOS71;..;;C:\DOS71\norton
C:\NET\netbind.com
C:\NET\umb.com
C:\NET\tcptsr.exe
C:\NET\tinyrfc.exe
C:\NET\nmtsr.exe
C:\NET\emsbfr.exe
C:\NET\net start

Protocol.ini configuration:

version=0x3110
netcard=amd$pcntnd,1,AMD$PCNTND,1
transport=ms$ndishlp,MS$NDISHLP
transport=ms$netbeui,MS$NETBEUI
transport=tcpip,TCPIP
lana0=amd$pcntnd,1,ms$netbeui
lana1=amd$pcntnd,1,ms$ndishlp
lana2=amd$pcntnd,1,tcpip

DefaultGateway0=192 168 171 2
NBSessions=6
SubNetMask0=255 255 255 0
IPAddress0=192 168 1 2
DisableDHCP=1
DriverName=TCPIP$
BINDINGS=AMD$PCNTND
LANABASE=1

DriverName=PROTMAN$
PRIORITY=MS$NDISHLP

drivername=pktdrv$
bindings=amd$pcntnd
intvec=0x60
chainvec=0x66

DriverName=PCNTND$
maxmulticasts=10
txbuffers=4
rxbuffers=4
;medium=_100full

DriverName=ndishlp$
BINDINGS=AMD$PCNTND

DriverName=netbeui$
SESSIONS=10
NCBS=12
BINDINGS=AMD$PCNTND
LANABASE=0

System.ini configuration:

sizworkbuf=1498
filesharing=no
printsharing=no
autologon=yes
computername=DOS USER C
lanroot=C:\NET
username=DOS USER
workgroup=MSHOME
reconnect=yes
dospophotkey=N
lmlogon=0
logondomain=WORKGROUP
preferredredir=full
autostart=full
maxconnections=8

netcard=pcntnd.dos
transport=*netbeui,tcpdrv.dos,nemm.dos,ndishlp.sys
devdir=C:\NET
LoadRMDrivers=yes

TimerCriticalSection=5000
UniqueDosPSP=TRUE
PSPIncrement=2

*Shares=C:\NET\Shares.PWL

I don't know why it always prompts "tcp is not loaded", and also "to load netbeui, the ndishlp.sys driver must be listed in the section of the system.ini file". I don't know where the problem is. Please help analyze it. Thanks

Floor1　connerxxx	Posted 2010-04-27 00:49
初级用户　Posts 31　Credits 73
I have installed the Microsoft Network Client for my DOS, but why can't the FTP command be enabled? I can't find the FTP command in the MNC directory. Is there any other program that hasn't been installed? I hope someone can help solve this problem! [ Last edited by connerxxx on 2010-4-29 at 00:51 ]

Floor2　goeasy2005	Posted 2010-04-28 15:48
中级用户　Posts 155　Credits 325
http://www.cn-dos.net/forum/viewthread.php?tid=3538&fpage=2 [ Last edited by goeasy2005 on 2010-4-20 at 15:53 ]

Floor3　connerxxx	Posted 2010-04-29 00:46
初级用户　Posts 31　Credits 73
Thanks, the source address couldn't be downloaded. Later, I found it in that post. There's another question I want to ask you. When the FTP runs, it prompts "no packet driver found", which should be that the network card driver isn't found. I'm using VMware to install DOS, installed MSClient, and the network card installed is VMware's pcntnd.dos. So I followed the instructions in the wattcp manual to try, but many problems occurred again. I don't know how to solve it. I tried many configuration methods but couldn't get it to work. The following is my own configuration file. I hope you can help see where the problem is. Thanks! Config.sys configuration: DEVICE=C:\DOS71\ECHO.SYS W/e/l/c/o/m/e /t/o MS-DOS 7.10... DEVICE=C:\DOS71\ECHO.SYS C/o/p/y/r/i/g/h/t M/i/c/r/o/s/o/f/t C/o/r/p. A/l/l /r/i/g/h/t/s /r/e/s/e/r/v/e/d. DEVICE=C:\DOS71\HIMEM.SYS/testmem:off DEVICE=C:\DOS71\EMM386.EXE noems novcpi DEVICEHIGH=C:\DOS71\SETVER.EXE REM DEVICEHIGH=C:\DOS71\POWER.EXE DEVICEHIGH=C:\DOS71\VIDE-CDD.SYS /D:IDE-CD REM DEVICEHIGH=C:\DOS71\DISPLAY.SYS CON=(,,1) COUNTRY=001,437,C:\DOS71\COUNTRY.SYS SHELL=COMMAND.COM /P /E:640 DOS=HIGH,UMB,AUTO FCBS=4,0 FILES=30 BUFFERS=15,0 LASTDRIVE=J STACKS=9,256 SET PATH=C:\DOS71;..;C:\MASM5.0;.\net device=C:\NET\ifshlp.sys devicehigh=c:\net\protman.dos /i:c:\net devicehigh=c:\net\dis_pkt.dos devicehigh=c:\net\pcntnd.dos devicehigh=c:\net\nemm.dos Autoexec.bat configuration: C:\NET\net initialize @ECHO OFF PROMPT $P$G SET DIRCMD=/4 MODE CON RATE=32 DELAY=1 REM MODE CON CP PREPARE=((437)EGA.CPI) REM MODE CON CP SELECT=437 REM KEYB US,,KEYBOARD.SYS LH KILLER LH DOSKEY LH DOSLFN /Z:C:\DOS71\CP437UNI.TBL REM LH MSCDEX /D:IDE-CD LH SHARE /L:30 REM LH NLSFUNC LH SMARTDRV REM LH CTMOUSE REM For compatiblity purpose: LH CTMOUSE > NUL ECHO. REM For locking volumes to enable "direct disk access": CALL LOCKDRV.BAT BREAK ON LFNFOR ON ECHO Now you are in MS-DOS 7.10 prompt. Type 'HELP' for help. ECHO. SET CTSYN=C:\SOUND SET MIDI=SYNTH:1 MAP:E MODE:0 SET BLASTER=A220 I5 D1 H5 P330 E620 T6 PATH=C:\NET;C:\DOS71;..;;C:\DOS71\norton C:\NET\netbind.com C:\NET\umb.com C:\NET\tcptsr.exe C:\NET\tinyrfc.exe C:\NET\nmtsr.exe C:\NET\emsbfr.exe C:\NET\net start Protocol.ini configuration: version=0x3110 netcard=amd$pcntnd,1,AMD$PCNTND,1 transport=ms$ndishlp,MS$NDISHLP transport=ms$netbeui,MS$NETBEUI transport=tcpip,TCPIP lana0=amd$pcntnd,1,ms$netbeui lana1=amd$pcntnd,1,ms$ndishlp lana2=amd$pcntnd,1,tcpip DefaultGateway0=192 168 171 2 NBSessions=6 SubNetMask0=255 255 255 0 IPAddress0=192 168 1 2 DisableDHCP=1 DriverName=TCPIP$ BINDINGS=AMD$PCNTND LANABASE=1 DriverName=PROTMAN$ PRIORITY=MS$NDISHLP drivername=pktdrv$ bindings=amd$pcntnd intvec=0x60 chainvec=0x66 DriverName=PCNTND$ maxmulticasts=10 txbuffers=4 rxbuffers=4 ;medium=_100full DriverName=ndishlp$ BINDINGS=AMD$PCNTND DriverName=netbeui$ SESSIONS=10 NCBS=12 BINDINGS=AMD$PCNTND LANABASE=0 System.ini configuration: sizworkbuf=1498 filesharing=no printsharing=no autologon=yes computername=DOS USER C lanroot=C:\NET username=DOS USER workgroup=MSHOME reconnect=yes dospophotkey=N lmlogon=0 logondomain=WORKGROUP preferredredir=full autostart=full maxconnections=8 netcard=pcntnd.dos transport=netbeui,tcpdrv.dos,nemm.dos,ndishlp.sys devdir=C:\NET LoadRMDrivers=yes TimerCriticalSection=5000 UniqueDosPSP=TRUE PSPIncrement=2 Shares=C:\NET\Shares.PWL I don't know why it always prompts "tcp is not loaded", and also "to load netbeui, the ndishlp.sys driver must be listed in the section of the system.ini file". I don't know where the problem is. Please help analyze it. Thanks