Thanks, the source address couldn't be downloaded. Later, I found it in that post. There's another question I want to ask you. When the FTP runs, it prompts "no packet driver found", which should be that the network card driver isn't found. I'm using VMware to install DOS, installed MSClient, and the network card installed is VMware's pcntnd.dos. So I followed the instructions in the wattcp manual to try, but many problems occurred again. I don't know how to solve it. I tried many configuration methods but couldn't get it to work. The following is my own configuration file. I hope you can help see where the problem is. Thanks!
Config.sys configuration:
DEVICE=C:\DOS71\ECHO.SYS W/e/l/c/o/m/e /t/o MS-DOS 7.10...
DEVICE=C:\DOS71\ECHO.SYS C/o/p/y/r/i/g/h/t M/i/c/r/o/s/o/f/t C/o/r/p. A/l/l /r/i/g/h/t/s /r/e/s/e/r/v/e/d.
DEVICE=C:\DOS71\HIMEM.SYS/testmem:off
DEVICE=C:\DOS71\EMM386.EXE noems novcpi
DEVICEHIGH=C:\DOS71\SETVER.EXE
REM DEVICEHIGH=C:\DOS71\POWER.EXE
DEVICEHIGH=C:\DOS71\VIDE-CDD.SYS /D:IDE-CD
REM DEVICEHIGH=C:\DOS71\DISPLAY.SYS CON=(,,1)
COUNTRY=001,437,C:\DOS71\COUNTRY.SYS
SHELL=COMMAND.COM /P /E:640
DOS=HIGH,UMB,AUTO
FCBS=4,0
FILES=30
BUFFERS=15,0
LASTDRIVE=J
STACKS=9,256
SET PATH=C:\DOS71;..;C:\MASM5.0;.\net
device=C:\NET\ifshlp.sys
devicehigh=c:\net\protman.dos /i:c:\net
devicehigh=c:\net\dis_pkt.dos
devicehigh=c:\net\pcntnd.dos
devicehigh=c:\net\nemm.dos
Autoexec.bat configuration:
C:\NET\net initialize
@ECHO OFF
PROMPT $P$G
SET DIRCMD=/4
MODE CON RATE=32 DELAY=1
REM MODE CON CP PREPARE=((437)EGA.CPI)
REM MODE CON CP SELECT=437
REM KEYB US,,KEYBOARD.SYS
LH KILLER
LH DOSKEY
LH DOSLFN /Z:C:\DOS71\CP437UNI.TBL
REM LH MSCDEX /D:IDE-CD
LH SHARE /L:30
REM LH NLSFUNC
LH SMARTDRV
REM LH CTMOUSE
REM For compatiblity purpose:
LH CTMOUSE > NUL
ECHO.
REM For locking volumes to enable "direct disk access":
CALL LOCKDRV.BAT
BREAK ON
LFNFOR ON
ECHO Now you are in MS-DOS 7.10 prompt. Type 'HELP' for help.
ECHO.
SET CTSYN=C:\SOUND
SET MIDI=SYNTH:1 MAP:E MODE:0
SET BLASTER=A220 I5 D1 H5 P330 E620 T6
PATH=C:\NET;C:\DOS71;..;;C:\DOS71\norton
C:\NET\netbind.com
C:\NET\umb.com
C:\NET\tcptsr.exe
C:\NET\tinyrfc.exe
C:\NET\nmtsr.exe
C:\NET\emsbfr.exe
C:\NET\net start
Protocol.ini configuration:
version=0x3110
netcard=amd$pcntnd,1,AMD$PCNTND,1
transport=ms$ndishlp,MS$NDISHLP
transport=ms$netbeui,MS$NETBEUI
transport=tcpip,TCPIP
lana0=amd$pcntnd,1,ms$netbeui
lana1=amd$pcntnd,1,ms$ndishlp
lana2=amd$pcntnd,1,tcpip
DefaultGateway0=192 168 171 2
NBSessions=6
SubNetMask0=255 255 255 0
IPAddress0=192 168 1 2
DisableDHCP=1
DriverName=TCPIP$
BINDINGS=AMD$PCNTND
LANABASE=1
DriverName=PROTMAN$
PRIORITY=MS$NDISHLP
drivername=pktdrv$
bindings=amd$pcntnd
intvec=0x60
chainvec=0x66
DriverName=PCNTND$
maxmulticasts=10
txbuffers=4
rxbuffers=4
;medium=_100full
DriverName=ndishlp$
BINDINGS=AMD$PCNTND
DriverName=netbeui$
SESSIONS=10
NCBS=12
BINDINGS=AMD$PCNTND
LANABASE=0
System.ini configuration:
sizworkbuf=1498
filesharing=no
printsharing=no
autologon=yes
computername=DOS USER C
lanroot=C:\NET
username=DOS USER
workgroup=MSHOME
reconnect=yes
dospophotkey=N
lmlogon=0
logondomain=WORKGROUP
preferredredir=full
autostart=full
maxconnections=8
netcard=pcntnd.dos
transport=*netbeui,tcpdrv.dos,nemm.dos,ndishlp.sys
devdir=C:\NET
LoadRMDrivers=yes
TimerCriticalSection=5000
UniqueDosPSP=TRUE
PSPIncrement=2
*Shares=C:\NET\Shares.PWL
I don't know why it always prompts "tcp is not loaded", and also "to load netbeui, the ndishlp.sys driver must be listed in the section of the system.ini file". I don't know where the problem is. Please help analyze it. Thanks
