My DOS: The Internet can be accessed, but the local area network cannot be accessed? - China DOS Union Forum

Within the local area network, both MSCLINET 3.0 and LAN MANAGER 2.2 were successfully installed and run. However, after running NET VIEW, it shows: "The list of machines in this workgroup cannot be obtained", that is, unable to access other computers. (But in Windows 2000 and XP, the computers in other workgroups are displayed normally.)

I've been struggling with this for several days without success, really depressed...

Hope some experts in this area can give some suggestions...

Regarding the installation of protocols, almost all combinations of the three protocols have been tried, but it doesn't work.

Hardware:
IBM T43P notebook, 160GB hard disk, 1GB memory, broadcom NetXtreme gigabit network card

DOS system:
DOS of Windows 95 (also tried DOS 6.22)

1
The installed protocols are IPX/NETBUEI/TCPIP (all kinds of combinations of the three)

2
The configuration is ordinary configuration, and there are no other programs.
CONFIG.SYS
=======================
DOS=HIGH,UMB,auto
DEVICE=c:\windows\HIMEM.SYS
device=c:\windows\emm386.exe noems
devicehigh=C:\NET\ifshlp.sys
=======================

AUTOEXEC.BAT
=========================
SET PATH=C:\NET
C:\NET\net initialize
C:\NET\netbind.com
C:\NET\umb.com
C:\NET\tcptsr.exe
C:\NET\tinyrfc.exe
C:\NET\nmtsr.exe
C:\NET\emsbfr.exe
C:\NET\net start

Supplementary favorable aspects:
1
Ping to the gateway and other addresses is successful, showing:
echo received from 123.346.789.789 roundtrip < 50 msec
2
According to the packet driver configuration to enter the system, ARAchNE and LYNX can be used to access the Internet... That is, the Internet can be accessed but the local area network cannot, which is very strange...

[ Last edited by GOTOmsdos on 2008-8-21 at 12:59 PM ]

Floor1　GOTOmsdos	Posted 2008-08-19 20:13
铂金会员　Posts 1,827　Credits 5,154
Within the local area network, both MSCLINET 3.0 and LAN MANAGER 2.2 were successfully installed and run. However, after running NET VIEW, it shows: "The list of machines in this workgroup cannot be obtained", that is, unable to access other computers. (But in Windows 2000 and XP, the computers in other workgroups are displayed normally.) I've been struggling with this for several days without success, really depressed... Hope some experts in this area can give some suggestions... Regarding the installation of protocols, almost all combinations of the three protocols have been tried, but it doesn't work. Hardware: IBM T43P notebook, 160GB hard disk, 1GB memory, broadcom NetXtreme gigabit network card DOS system: DOS of Windows 95 (also tried DOS 6.22) 1 The installed protocols are IPX/NETBUEI/TCPIP (all kinds of combinations of the three) 2 The configuration is ordinary configuration, and there are no other programs. CONFIG.SYS ======================= DOS=HIGH,UMB,auto DEVICE=c:\windows\HIMEM.SYS device=c:\windows\emm386.exe noems devicehigh=C:\NET\ifshlp.sys ======================= AUTOEXEC.BAT ========================= SET PATH=C:\NET C:\NET\net initialize C:\NET\netbind.com C:\NET\umb.com C:\NET\tcptsr.exe C:\NET\tinyrfc.exe C:\NET\nmtsr.exe C:\NET\emsbfr.exe C:\NET\net start Supplementary favorable aspects: 1 Ping to the gateway and other addresses is successful, showing: echo received from 123.346.789.789 roundtrip < 50 msec 2 According to the packet driver configuration to enter the system, ARAchNE and LYNX can be used to access the Internet... That is, the Internet can be accessed but the local area network cannot, which is very strange... [ Last edited by GOTOmsdos on 2008-8-21 at 12:59 PM ]