China DOS Union
-- Unite DOS · Advance DOS · Grow DOS --Union site: www.cn-dos.net Forum site: www.cn-dos.net/forum
|
China DOS Union-- Unite DOS · Advance DOS · Grow DOS --Union site: www.cn-dos.net Forum site: www.cn-dos.net/forum |
| Guest | Log in | Register | Members | Search | China DOS Union |
|
中国DOS联盟论坛 The time now is 2026-10-27 20:33 |
47,815 topics / 349,929 posts / today 1 new / 48,290 members |
| DOS启动盘 & LOGO技术 （启动盘室） » The moderator's USB mouse driver hangs as soon as I use it |
| Printable Version 2,112 / 12 |
| Floor1 pluto_zj | Posted 2003-05-04 00:00 |
| 初级用户 Posts 19 Credits 162 | |
|
I'm using an A4Tech USB mouse. I added device=ohci.exe in CONFIG.SYS (the one from USB LINKER 2.5), and after rebooting the system shows:
usb link, usb stack driver,ver 2.5 ......................................... OHCI USB Controller initialized....... Then it just hangs there and won't move, with no response at all. I tried replacing OHCI with UHCI; although it doesn't hang, it can't detect the device. Please help, experts! |
|
| Floor2 如是大师 | Posted 2003-05-04 00:00 |
| 元老会员 Posts 3,351 Credits 9,654 From 湖北 | |
|
Is your motherboard an 845?
|
|
| Floor3 Wengier | Posted 2003-05-04 00:00 |
| 系统支持 Posts 10,521 Credits 27,736 | |
|
Did you load EMM386 or UMBPCI?
|
|
| Floor4 pluto_zj | Posted 2003-05-04 00:00 |
| 初级用户 Posts 19 Credits 162 | |
|
It's an FUJISTU P2040 laptop, the CPU is CRUSOE, motherboard model unknown, and I'm loading EMM386.
|
|
| Floor5 Wengier | Posted 2003-05-04 00:00 |
| 系统支持 Posts 10,521 Credits 27,736 | |
|
Try removing EMM386 and then loading OHCI.
|
|
| Floor6 pluto_zj | Posted 2003-05-04 00:00 |
| 初级用户 Posts 19 Credits 162 | |
|
It's working now. After removing EMM386 it can load, so I guess this is the only way. My motherboard can't use UMBPCI either, how depressing~~
|
|
| Floor7 Wengier | Posted 2003-05-04 00:00 |
| 系统支持 Posts 10,521 Credits 27,736 | |
|
Since that's the cause, then it's easy to deal with. You only need to add the X=D000 parameter to EMM386 and OHCI will run.
|
|
| Floor8 pizigao | Posted 2003-05-09 00:00 |
| 银牌会员 Posts 292 Credits 1,063 | |
|
What does X mean!!!???
|
|
| Floor9 Wengier | Posted 2003-05-09 00:00 |
| 系统支持 Posts 10,521 Credits 27,736 | |
|
X is a parameter of EMM386. It means excluding the specified memory address. If you add the X=D000 parameter, OHCI.EXE should be able to run normally.
|
|
| Floor10 pizigao | Posted 2003-05-10 00:00 |
| 银牌会员 Posts 292 Credits 1,063 | |
|
Learned a new trick again!!!
|
|
| Floor11 wangnan16 | Posted 2003-05-25 00:00 |
| 初级用户 Posts 15 Credits 143 | |
|
I have this problem too
|
|
| Floor12 kaka2008 | Posted 2004-10-29 00:00 |
| 初级用户 Posts 1 Credits 102 | |
|
My laptop is a Lenovo Zhaoyang E200 notebook. On it, even if I remove the emm386.exe line from config,sys, OHCI.exe still won't run; it hangs after running it. Running UHCI.exe can't detect the device. Everyone, please help. My laptop has to install some software to drive the mouse under MS-DOS mode, otherwise it has no PS2 mouse port.
|
|
| Floor13 猫飞飞 | Posted 2004-10-30 00:00 |
| 初级用户 Posts 14 Credits 157 | |
|
Haha. OHCI.exe and UHCI.exe, these two USB mouse drivers, are not very complete. Running GHOST and Microsoft's edit.com is no problem. Running other DOS programs, mouse-supported programs, may cause errors. For DOS programs, a PS/2 mouse is still easier to use. I suggest you use the kind of optical mouse with a USB---PS/2 adapter. That's what I use. A Tsinghua Tongfang one. 80 yuan.
|
|
|
[ Contact the Union admin team -
中国DOS联盟 -
Standard version ] Sponsored by ifanr Inc | © 2001–2023 |