China DOS Union
-- Unite DOS · Advance DOS · Grow DOS --Union site: www.cn-dos.net Forum site: www.cn-dos.net/forum
|
China DOS Union-- Unite DOS · Advance DOS · Grow DOS --Union site: www.cn-dos.net Forum site: www.cn-dos.net/forum |
| Guest | Log in | Register | Members | Search | China DOS Union |
|
中国DOS联盟论坛 The time now is 2026-08-15 20:40 |
47,813 topics / 349,903 posts / today 1 new / 48,258 members |
| DOS疑难解答 & 问题讨论 （解答室） » Experts, please help: |
| Printable Version 800 / 7 |
| Floor1 sean5018 | Posted 2003-03-25 00:00 |
| 初级用户 Posts 5 Credits 124 | |
|
Experts, please help:
The situation is as follows. When the external hard drive is connected to the USB port, if I boot with a Win98 startup disk (with duse.exe set to load in config.sys), the machine hangs when that driver finishes loading. If I boot with a WinME startup disk (with duse.exe set to load in config.sys), it can run until the A: prompt appears, and then it hangs. In both cases, warm boot also does not work. How can I solve this? |
|
| Floor2 Wengier | Posted 2003-03-25 00:00 |
| 系统支持 Posts 10,521 Credits 27,736 | |
|
Then what happens when you use my MS-DOS 7.10 boot disk to load DUSE.EXE:
http://newdos.yginfo.net/dosware/mdos71bd.zip |
|
| Floor3 sean5018 | Posted 2003-03-26 00:00 |
| 初级用户 Posts 5 Credits 124 | |
|
Hi Wengier,
I downloaded the startup disk from the address you gave, but it's still the same old problem. It shows UCHI USB Controller initialized (I/O 0*600 IRQ 5) UCHI USB Controller initialized (I/O 0*640 IRQ 11) and then stops there. But after unplugging the external usb drive, it can boot. Could it be that there is a problem with my external drive or motherboard? Thanks |
|
| Floor4 Wengier | Posted 2003-03-26 00:00 |
| 系统支持 Posts 10,521 Credits 27,736 | |
|
When it stops there, pressing the ESC key should cancel it, right.
|
|
| Floor5 dda_bing | Posted 2003-03-27 00:00 |
| 初级用户 Posts 4 Credits 112 | |
|
I ran into a few problems when using DUSE. First, it seems to need upper memory. Second, this driver seems to be picky about chipsets; some chipsets cannot be recognized. I don't know the reason. Among the ones I could buy on the market, the only one that worked was INSYSTEM.
|
|
| Floor6 sean5018 | Posted 2003-03-27 00:00 |
| 初级用户 Posts 5 Credits 124 | |
|
Pressing ESC didn't work either, but after I switched to motto it worked. Thanks
|
|
| Floor7 sean5018 | Posted 2003-03-27 00:00 |
| 初级用户 Posts 5 Credits 124 | |
|
Thanks
|
|
| Floor8 ko20010214 | Posted 2003-07-04 00:00 |
| 版主 Posts 1,628 Credits 7,296 | |
|
First learn how to ask a question.
Change your post title to something better. In the future, posts with this kind of title may end up with only these three outcomes: 1。Nobody pays attention to it. (This is the best case.) 2。It gets moved to the chatter section. 3。It gets deleted. |
|
|
[ Contact the Union admin team -
中国DOS联盟 -
Standard version ] Sponsored by ifanr Inc | © 2001–2023 |