China DOS Union

Who has the usage instructions for Motto Hairu, please inform me

Motto Hairu has English and Japanese descriptions.

Motto Hairu after download is all:
…………The devices that can be recognized, also can't be connected to be loaded, and need to be operated in DOS of USB devices.
The recognized device is like this. Under the condition of IEEE1394 devices, the operation in DOS can't be carried out.…………

It's under "New DOS Era", who has a readable instruction file ah?~~~

I have an English manual
http://www.stefan2000.com/darkehorse/PC/DOS/Drivers/USB/readme.txt
I compare it with the original text and find it a bit similar, right? I wonder which country's English the original text is?

----------
"motto hairu" DOS Driver
----------

This driver enables the "motto hairu" USB interface on DOS.
The IEEE1394 interface cannot be used on DOS.

There are three drivers as DOS drivers.

USBASPI.SYS : USB1.1 mode ASPI Manager
RAMFD.SYS : RAM DISK driver for USB floppy, if you have only a single USB port and need to access both.
Di1000dd.SYS : ASPI HDD driver

1. If you do not have a USB floppy

Copy the USBASPI.SYS and Di1000dd.SYS files and
add the following 2 lines to the config.sys on the boot disk.

device=USBASPI.SYS
device=Di1000dd.SYS

After that, connect the "motto hairu" to the USB port, then set this disk as the FDD, and
power on the PC.


2. If you use a USB floppy

Copy the USBASPI.SYS, Di1000dd.SYS and RAMFD.SYS files and
add the following 3 lines to the config.sys on the boot disk.

device=RAMFD.SYS
device=USBASPI.SYS /W@@@@---@Use /R option if you have multiple USB ports
device=Di1000dd.SYS

And confirm
device=himem.sys
exists in config.sys.
If you don't have it, add the following 4 lines.

device=himem.sys
device=RAMFD.SYS
device=USBASPI.SYS /W
device=Di1000dd.SYS

When powering on, during booting, the contents of the FD are copied to the RAM disk, then,
when the copy is completed, the following message will appear.

===============================================
=== Connect the target device to USB port. ===
=== Press



key.
Booting will continue from the RAM disk.

NOTE:
1) After changing the DOS mode by rebooting Windows, it will not work.
You must power off once.

2) Option settings

USBASPI.SYS has the following options.

/R : Also access USB FDD.
: RAMFD.SYS may be needed in some cases.

/W : Prompt the following message for swapping floppy and device if you need to boot from
USB floppy and have only one USB port

===============================================
=== Connect the target device to USB port. ===
@@ === Press





















-> -> .
2. Double click icon.
3. Click tab.
4. Double click .

************* Universal Host Controller
means UHCI is used.

************* Open Host Controller
means OHCI is used.

[ Last edited by 雨露 on 2006-11-13 at 12:05 AM ]

Unfortunately, there are still one or two "gibberish" parts in the middle, which is not perfect!

----------
"[User's motto, hairu]" DOS Driver
----------

This driver enables "[User's motto, hairu]" to work with USB interface DOS.
IEEE1394 interface cannot be used with DOS.

There are 3 drivers as DOS drivers.

usbaspi.sys: usb1.1 mode aspi manager
ramfd.sys: RAM disk driver, USB floppy, if you only have a single USB port and get two.
di1000dd.sys: aspi hard drive

1. If you don't have USB floppy

Copy usbaspi.sys and di1000dd.sys files and
Add the following 2 lines to Config.sys on the boot disk.

DEVICE=usbaspi.sys
DEVICE=di1000dd.sys

Then, connect "[User's motto, hairu]" to the USB port, then set this disk as RAMFD, and
Power on the PC.


2. If you use USB floppy

Copy usbaspi.sys, di1000dd.sys and ramfd.sys files and
Add the following 3 lines to Config.sys on the boot disk.

DEVICE=ramfd.sys
DEVICE=usbaspi.sys /W@@@@@ ---Use /R option if you have multiple USB ports
DEVICE=di1000dd.sys

And confirm
DEVICE=HIMEM.SYS
exists in Config.sys.
If you don't, add the following 4 lines.

DEVICE=HIMEM.SYS
DEVICE=ramfd.sys
DEVICE=usbaspi.sys /W
DEVICE=di1000dd.sys

When powered on, during boot, the contents of FD are copied to RAM disk, then,
When the copy is complete, the following message will appear.

===============================================
===Connect target device to USB port. ===
===Press [Enter] to continue. ===
===============================================

Then, disconnect the USB floppy from the USB port and connect "[User's motto, hairu]" to the USB port and
Press [Enter] key.
Boot will continue from RAM disk.

Note:
1) After changing and restarting Windows in DOS mode, it won't work.
You must power off once.

2) Option settings

usbaspi.sys has the following options.

Commercial/Residential: Access USB and RAMFD.
: ramfd.sys may be needed in some cases.

/W: Prompt the following message to swap floppy and device if you need to boot from
USB floppy and only one USB port

===============================================
===Connect target device to USB port. ===
@ @ ===Press [Enter] to continue. ===
===============================================

/M=XX: ohci memory map address
By default, it will use the unused address between d0000h and dfffffh.
E.g.) /M=D4: use d4000h

/P=xxx0: uhci I/O address
Specify if BIOS doesn't assign I/O port address to controller.
/V: Display various information.

3) In case of ohci, emm386.exe is not recommended.
@ @ If you use it, please don't use umb or specify x=d000-dfff to keep expanding ROM space.
4) In some PCs, uhci I/O port is not assigned by BIOS.
In this case, specify I/O port by /P option.

Appendix: fabout ohci and uhci
There are 2 kinds of USB host controller chip specifications.
Universal Host Controller Interface = uhci
Open Host Controller Interface = ohci

We can check which one is used with the following procedure.
1. Click [Start] -> "[Settings (S)]" -> "[Control Panel (C)]".
2. Double-click [System] icon.
3. Click [Device Manager] tab.
4. Double-click [Universal Serial Bus controllers].

*************Universal Host Controller
uhci means is used.

*************Open Host Controller
ohci means is used.

--------------------------------------------------
It is more DOS drivers
--------------------------------------------------
The drivers are here for more USB interfaces to be used in DOS. If it's an IEEE1394 interface, DOS cannot use it.

The drivers are the following three drivers.

usbaspi.sys: usb1.1 mode ASPI manager.
ramfd.sys: Only for USB port, USB floppy, and if you want to use and coexist with USB floppy, the RAM disk driver.
di1000dd.sys: ASPI driver for hard disk.

1. If using USB floppy
If you have a boot disk, copy usbaspi.sys and di1000dd.sys to the Config.sys file and add the following two lines at the end.

DEVICE=usbaspi.sys
DEVICE=di1000dd.sys

For this change, connect to a USB port, set the boot disk to the FD and boot from the boot disk.

2. If using USB floppy 2
If you have a boot disk, copy usbaspi.sys, di1000dd.sys, ramfd.sys to the Config.sys file and add the following three lines at the end.

DEVICE=ramfd.sys
DEVICE=usbaspi.sys /W --- For multiple USB interfaces, USB floppy and products at the same time, if you can connect to the USB port, commercial/residential can be selected.
DEVICE=di1000dd.sys

Also, make sure to list DEVICE=HIMEM.SYS in Config.sys. If this section doesn't exist, add the following four lines.

DEVICE=HIMEM.SYS
DEVICE=ramfd.sys
DEVICE=usbaspi.sys /W
DEVICE=di1000dd.sys

After successfully running the boot disk to start the process of FD and the content of the RAM disk copying is completed, the following message will appear.

===============================================
===Connect the target device to the USB port.===
===Press [Enter] to continue.===
===============================================

When you receive this message, remove the USB floppy from the USB port, plug in a USB port, and press Enter. The PC will continue to start. (I made the RAM disk boot.)


Note:
1) After restarting Windows, immediately entering DOS mode is not available. Make sure to power off the PC and start from the beginning.
2) Other optional settings: Set the following options for usbaspi.sys.
Commercial/residential electricity: USB FD combined with related cases.
: Depending on your PC, ramfd.sys may be needed.

/W: USB floppy is accompanied by the demonstration port of the USB port, which is only 1 model from the floppy DOS (Windows) start, and the floppy and USB device can be used instead.
The following message prompt is as follows.
===============================================
===Connect the target device to the USB port.===
===Press [Enter] to continue.===
===============================================

/M=XX: ohci specifies memorimappuadoresu. The default search from this email address is d0000h to dffffh, which seems to be unused. For example) /M=D4: use d4000h.

/P=xxx0: uhci I/O address you want. The controller's body BIOS I/O port address has been assigned the most when not specified.
/V: various information.
3) For ohci cases, do not use emm386.exe as much as possible. If you are using umb or not using a set, set X=D000-DFFF ROM space expansion, please go out.
4) The BIOS of uhci and I/O port mechanism is not in the specified mode. Such a mode/P option I/O port must be specified.

Supplement: About ohci and uhci.
The USB standards of hosutokontororachippu are the following two.
Universal Host Controller Interface = uhci
Open Host Controller Interface = ohci
Both are explained in detail here, and you can have your PC or both standards in the following way.
1. Start "-> [Settings (S)] -> [Control Panel (C)] button.
2. [System], double-click the icon.
3. In the Device Manager tab.
4. Universal Serial Bus controllers, double-click.

*************Universal Host Controller
If it is shown, uhci is used.

*************Open Host Controller
If it is shown, ohci is used.