China DOS Union

This is the Wubi package.

Correction: There is an error in the instruction file: Smart Wubi is called up with Alt+F4!

[ Last edited by 本是 on 2008-12-19 at 11:18 ]

Thanks to the master!
Under XP, it cannot be used normally. After entering the UCDOS interface, the drive letter cannot appear. It is approximately a deadlock.
I don't like that larger UCDOS. It can be used normally. If you need to modify, you can consider using that one.

Originally posted by julon at 2008-12-19 06:12:
Thanks, Master Ben Shi!
Under XP, it can't work properly. After entering the UCDOS interface, the drive letters don't appear. It's almost stuck.
I don't like the larger UCDOS. The one that can work normally, if you need to modify, you can consider using that one.

Here, if I execute respectively:
rd16
knl
limd py4
cwb
It's completely normal.
Writing the above content into ucdos.bat and executing is also completely normal.
My XP is SP3 3300.

Please send me that "larger KNL.COM".
Also, thank you for your XCab!

[ Last edited by 本是 on 2008-12-19 at 08:51 ]

Executing ucdos.bat causes a crash or screen corruption, but entering them individually is fine!

Just now I checked. In the post "The most streamlined UCDOS! (two input methods: intelligent Pinyin and Wubi) http://www.cn-dos.net/forum/viewthread.php?tid=39448&fpage=1, the KNL.COM/RDXM.COM are exactly the same as mine. The only difference is that my information in KNL is deleted, and there is no explanation at all! The same KNL, it can't be that his can pass and mine can't, that's not logical! His Pinyin input is more than 100K, and my PY4 plus intelligent Wubi is only about 60K.

Originally posted by Yulu at 2008-12-19 09:51:
Writing to ucdos.bat and executing it will cause a crash or screen corruption, but entering them separately is fine!

My XP - whether XP2 or XP3 can execute ucdos.bat. Maybe everyone is using a streamlined version of XP, and the 16-bit DOS is somewhat incomplete. My solution is to install the 16-bit DOS components of SOULdiy, and it will work.

[ Last edited by Ben Shi on 2008-12-19 at 10:07 ]

Just execute each line of commands in the batch file separately. When running ucdos.bat, there is no response in full screen. At this time, pressing alt+enter returns to the prompt.

UCDOS may also need a MS-DOS shortcut generated from the system32\command.com, set to full screen and compatible with 98 settings.

The XP I'm using is a streamlined version, and the master is right!

Placed in the MSDOS 7.1 boot disk, it's perfect! But it doesn't work when placed in a pure DOS boot disk (three basic files), and it prompts that the parameter is incorrect.

Originally posted by Yulu at 2008-12-19 16:47:
Placed in the msdos7.1 boot disk, very perfect!
But it doesn't work when placed in a pure DOS boot disk (three basic files), prompting incorrect parameters.

Please send this pure DOS boot disk image to born2be@126.com. Let me take a look.
Actually, I also have a version that needs to remove the DRV path, which only needs the \UCDOS directory. The size is the same as the current version. The difference is only in KNL and limd.

Through the method of elimination, it is found that the pure DOS boot disk, that is, only the three files command.com, msdos.sys, io.sys, plus the ucdos directory, and the AUTOEXEC.BAT containing only the following content
---------------------
cd ucdos
RD16.COM
KNL.COM
cwb.com
----------------------
cannot successfully run to the UCDOS platform.
Adding a himem.sys file can do it!

What is puzzling is that the extended memory management program HIMEM.SYS does not need to be configured in CONFIG.SYS, and the CONFIG.SYS file can be omitted. Probably because UCDOS needs to call HIMEM.SYS!

Originally posted by Yulu at 2008-12-20 09:51:
Through the elimination method, it is found that the pure DOS boot disk, that is, only the three files command.com, msdos.sys, io.sys, plus the ucdos directory, and AUTOEXEC.BAT containing only the following content
---------------------
cd ucdos
RD16.COM
KNL.COM
c ...

That's because my RD16 has been streamlined to only leave the XMS memory font library driver. Using the original full-function version of rd16 should be okay.

I can't use it under DOSBOX. Who can help me? Thanks