China DOS Union

-- Unite DOS · Advance DOS · Grow DOS --
Union site: www.cn-dos.net　Forum site: www.cn-dos.net/forum

中国DOS联盟论坛
The time now is 2026-10-25 02:52

47,815 topics / 349,928 posts / today 0 new / 48,288 members

DOS开发编程 & 发展交流（开发室） » Disk sector reading and writing, partition information management tool Dsptw (updated on 2008.11.29)

Printable Version 　126,061 / 565

Floor511　wewebb	Posted 2009-10-10 19:54
初级用户　Posts 53　Credits 66
A great tool for absolute sector reading and writing. The instructions are very detailed.

Floor514　jianliulin	Posted 2009-11-20 15:38
新手上路　Posts 3　Credits 5
The software I've been looking for for a long time

Floor515　jianliulin	Posted 2009-11-20 19:33
新手上路　Posts 3　Credits 5
LZ, can you remove the function of executing with a limited name? When I load dsptw into memory and then execute it, the program gets blocked.

Floor516　atoms	Posted 2009-11-21 02:20
初级用户　Posts 28　Credits 182
Is there a diskrw.com for pure DOS below 13KB, used in 64kb, freedos?

Floor517　123456	Posted 2009-12-01 15:19
初级用户　Posts 9　Credits 128
You are the version below, I changed the search order

Floor519　gaoruxing	Posted 2009-12-17 10:09
新手上路　Posts 1　Credits 2
Great stuff, thanks for sharing!

Floor520　AhKang	Posted 2009-12-25 16:16
初级用户　Posts 21　Credits 42
Most directories (Chinese/English) placed under drive E: can run normally (C: partition is normally displayed, but there are exceptions for individual directories). However, once placed in any location (including the root directory) of drive D: or C:, it appears like this - C: partition is not displayed (is it a parameter error? But the same command runs without error under drive E:!). I sincerely request the original poster to take time from their busy schedule to take a look and provide a solution. [ Last edited by AhKang on 2009-12-25 at 16:22 ] Attachments NoC.PNG (9.17 KiB) HasC.PNG (59.76 KiB) CNDirHasC.PNG (66.04 KiB)

Floor521　cjing2000	Posted 2009-12-26 14:04
新手上路　Posts 1　Credits 2
Download and test it. Unexpectedly, the two integrated files are so much smaller.

Floor522　19951001	Posted 2009-12-26 15:52
高级用户　Posts 272　Credits 570　From 北京
There is no such situation here. Attachments 111.GIF (16.36 KiB)

Floor523　wyl0205	Posted 2009-12-28 13:03
新手上路　Posts 1　Credits 2
I don't know if the number of hard drives can be detected

Floor524　AhKang	Posted 2010-01-04 16:20
初级用户　Posts 21　Credits 42
The corresponding command is: dsptw n /L (n = 0 (the first hard disk, n = 1 is the second hard disk... and so on) until the maximum number of hard disks. If the command appears "Open Disk Error!", it means that the number of your hard disks is the number you just entered. For example, in a computer with only one hard disk, entering dsptw 0 /L is okay, but if you enter dsptw 1 /L, then "Open Disk Error!" will appear. That is to say, your hard disk is the number you just entered, which is 1 (only one hard disk, right?) At least this is how I understand it. If there are any improper places, I hope the experts on the forum will criticize and correct. [ Last edited by AhKang on 2010-1-4 at 16:21 ]

Floor525　3mile	Posted 2010-01-11 22:10
新手上路　Posts 1　Credits 2
Good stuff, especially GETID is very useful ha

Prev　 1 … 32 33 34 35 36 37 38 　Next