标题: [已解决]如何使用 reg 命令修改注册表？ [打印本页]

---

作者: chishingchan     时间: 2007-7-6 16:25    标题: [已解决]如何使用 reg 命令修改注册表？

我有个注册表信息（修改工作站分辨）想用 REG 命令修改注册表，虽然批处理时显示操作已经完成，但注册表信息无变化！不知什么原因，求教。

Windows Registry Editor Version 5.00

[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Services\BeTwinDD\Device1]
"DefaultSettings.VRefresh"=dword:0000004b
"DefaultSettings.BitsPerPel"=dword:00000020
"DefaultSettings.XResolution"=dword:00000400
"DefaultSettings.YResolution"=dword:00000300

[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\Current\System\CurrentControlSet\Services\BeTwinDD\Device1]
"DefaultSettings.VRefresh"=dword:0000004b
"DefaultSettings.BitsPerPel"=dword:00000020
"DefaultSettings.XResolution"=dword:00000400
"DefaultSettings.YResolution"=dword:00000300

以下是个的失败作品：
reg add "HKLM\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Services\BeTwinDD\Device1" /v DefaultSettings.XResolution /t REG_DWORD /d 00000400 /f
reg add "HKLM\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Services\BeTwinDD\Device1" /v DefaultSettings.YResolution /t REG_DWORD /d 00000300
reg add "HKLM\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Services\BeTwinDD\Device1" /v DefaultSettings.BitsPerPel /t REG_DWORD /d 00000020
reg add "HKLM\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Services\BeTwinDD\Device1" /v DefaultSettings.VRefresh /t REG_DWORD /d 0000004b
reg add "HKLM\SYSTEM\CurrentControlSet\Hardware Profiles\Current\System\CurrentControlSet\Services\BeTwinDD\Device1" /v DefaultSettings.XResolution /t REG_DWORD /d 00000400
reg add "HKLM\SYSTEM\CurrentControlSet\Hardware Profiles\Current\System\CurrentControlSet\Services\BeTwinDD\Device1" /v DefaultSettings.YResolution /t REG_DWORD /d 00000300
reg add "HKLM\SYSTEM\CurrentControlSet\Hardware Profiles\Current\System\CurrentControlSet\Services\BeTwinDD\Device1" /v DefaultSettings.BitsPerPel /t REG_DWORD /d 00000020
reg add "HKLM\SYSTEM\CurrentControlSet\Hardware Profiles\Current\System\CurrentControlSet\Services\BeTwinDD\Device1" /v DefaultSettings.VRefresh /t REG_DWORD /d 0000004b

[ Last edited by chishingchan on 2007-7-7 at 03:41 AM ]

---

作者: chishingchan     时间: 2007-7-7 00:25
各位大虾帮忙一下吧！

---

作者: lxmxn     时间: 2007-7-7 00:56
把/d后面的16进制值改成10进制的形式试试。

---

作者: chishingchan     时间: 2007-7-7 03:35
试试再说，先谢了！

---

作者: chishingchan     时间: 2007-7-7 03:40
lxmxn 版主果然厉害！我测试成功了，谢谢！