标题: WMIC输出是否可以自定义 [打印本页]
作者: everest79 时间: 2007-2-27 01:20 标题: WMIC输出是否可以自定义
wmic process get processid,executablepath
以上两项输出自定义processid为第一列，executablepath为第二列，可否？@echo off
::view connection by:everest@cn-dos.net
::!executablepath-expand-LO!set adv= wmicprocess where handle="%dtp%" get executablepath|find /v /i "executablepath"
:top
ECHO Simple Netstat 网络连接查看器 timeon:%time:~0,-3%
ECHO --------------------------------------------------------------------------------
ECHO 本机地址/端口 远程地址/端口 连接状态 进程 进程名称
for /f "skip=4 tokens=*" %%i in ('netstat -abn') do (
set nh=%%i x
call set nha=%%nh:]=%%
echo %%i|findstr /b "[">nul&&call echo %%nhb%% %%nha:~1,12%%||call set nhb=%%nh:~0,3%%:%%nh:~7,21%%-%%nh:~30,21%% %%nh:~53,11%% %%nh:~69,5%%&&call set adv=%%nh:~69,5%%
)
ECHO.&ECHO steering command: (r)refresh (c)close (cls)clear screen&ECHO.
:input
set /p cc="%CD%\netuse>"
if /i not "%cc%" == "cls" (if /i not "%cc%" == "r" (if /i not "%cc%" == "c" (goto input) else (exit/b)) else (echo/&echo.&echo\&goto top)) else (cls&goto input)
不满足的是没有一个简单快捷的方法获取进程完整路径::view connection by:everest@cn-dos.net
::!executablepath-expand-LO!set adv= wmicprocess where handle="%dtp%" get executablepath|find /v /i "executablepath"
:top
ECHO Simple Netstat 网络连接查看器 timeon:%time:~0,-3%
ECHO --------------------------------------------------------------------------------
ECHO 本机地址/端口 远程地址/端口 连接状态 进程 进程名称
for /f "skip=4 tokens=*" %%i in ('netstat -abn') do (
set nh=%%i x
call set nha=%%nh:]=%%
echo %%i|findstr /b "[">nul&&call echo %%nhb%% %%nha:~1,12%%||call set nhb=%%nh:~0,3%%:%%nh:~7,21%%-%%nh:~30,21%% %%nh:~53,11%% %%nh:~69,5%%&&call set adv=%%nh:~69,5%%
)
ECHO.&ECHO steering command: (r)refresh (c)close (cls)clear screen&ECHO.
:input
set /p cc="%CD%\netuse>"
if /i not "%cc%" == "cls" (if /i not "%cc%" == "r" (if /i not "%cc%" == "c" (goto input) else (exit/b)) else (echo/&echo.&echo\&goto top)) else (cls&goto input)
大家新年好
[ Last edited by everest79 on 2007-2-27 at 09:57 PM ]
作者: lxmxn 时间: 2007-2-27 01:58
| Quote: | |
|
感谢新年作品，获取进程完整的路径可以用WMIC：
wmic process get commandline
作者: oilio 时间: 2007-2-27 02:03
wmic process get commandline,caption
感觉这样看得更清楚一点。
作者: everest79 时间: 2007-2-28 05:28
本来想在执行netstat之前生成当前系统进程path变量表，例如 _pid8=C:\windows\system32\svchost.exe
但使用wmic process get processid,executablepath输出的表格中executablepath始终在pid前边，而路径比较复杂，没办法在for中取得完整路径与pid
for /f "skip=4 tokens=1,2" %%i in ('"wmic process get processid,executablepath"') do set _pid%%j=%%i
请问有没有办法自定义表格输出？后来打算每行都执行以下代码，但显示速度就有点慢
wmicprocess where handle="%dtp%" get executablepath|find /v /i "executablepath"
作者: everest79 时间: 2007-2-28 20:34
请大家指点
作者: everest79 时间: 2007-3-3 06:06
再请教，呵呵
作者: kinpol 时间: 2008-4-30 20:46
请问 怎么用vc6来调用wmic进行编程，是不是还得windows DDK进行辅助编程？？请指教