中文PXE网络克隆维护系统 Beta 2.1
用基于PXE的工作站远程引导镜象原理,工作站实现无光驱、无软驱、无U盘就可以成功的引导系统;进入网克维护系统界面,进行系统恢复与备份,以及分区格式化,NTFS访问等, 对于每一个维护系统的人员来说,无疑是有极大的好处;更重要的是相当方便!
本程序系本人利用业余时间完成,仅供本人研究和使用; 其程序版权以及相关技术归原著作者所有,不得用于任何形式的商业用途,否则发生任何纠纷均与本人无关!
以下是废话,可以略过.
使用方法很简单,只要你的爱机支持PXE引导功能,怎么支持,在你的COMS里面找吧,我不好一一说明了.万一要是不支持呢? 废话! 不支持还网克什么? 不过呢,也不是没办法的, 就是麻烦了点. 可以加PXE引导芯片, 或是刷BOIS代码,具体方法,自已找找资料吧.万一要是几十上百台,我的妈啊,你不可能一台一台去刷吧,现在的主板大都集成PXEROM的了,除非是老古董了.
具体操作方法如下:
1. 1> 设置网克服务端的IP: 10.1.1.1 Netmask: 255.0.0.0
优点: 快速方便,客户端无需任何设定,较多机器时相当好. 缺点:需要修改服务器IP和子网掩码.
2> 设置网克服务端的IP、子网掩码为当前,客户端通过调整WATTCP.CFG配置文件自动网克.
优点: 不用修改服务器IP和子网掩码,机器不多时很好. 缺点: 需要每台更改客户机WATTCP配置.
3> 设置网克服务端的IP、子网掩码为当前,客户端启用手动GHOST选定会话,自动获取IP网克.
优点: 不用修改服务器IP和子网掩码. 缺点: 有时无法找到DHCP服务,相当郁闷!
2. 打开Tftpd32,保留2项即可,即(TftpServer、DHCPServer),填好起始IP地址,和容纳的IP个数\子网掩码,
启动文件名为mba.pxe 注意IP地址池必须跟网克服务器IP保持同一网段,否则无法下载镜象.
3. 打开GhostSrv网克服务端,设置会话名称为: NET 以及镜象文件位置.根据情况选择分区或者是磁盘,
点击接受客户机.
4. 客户机设置从PXE引导,从服务器下载镜象到客户机系统,进入PXE网络克隆维护系统,第一项加载
网卡驱动,OK后选择要克隆的分区或磁盘.
5. 服务端接受到客户机信息,点击发送数据,开始网克...
下载地址:
http://hulongzhuo.ys168.com
Last edited by hulongzhuo on 2007-7-12 at 02:03 PM ]
Chinese PXE Network Cloning Maintenance System Beta 2.1
Using the principle of remote boot image based on PXE for workstations, workstations can successfully boot the system without CD-ROM, floppy drive, or USB flash drive; enter the network cloning maintenance system interface, perform system restoration and backup, as well as partition formatting, NTFS access, etc. For every person maintaining the system, it is undoubtedly of great benefit; more importantly, it is quite convenient!
This program was completed by me in my spare time, for my own research and use only; the program copyright and related technologies belong to the original author, and it cannot be used for any form of commercial use, otherwise any disputes shall be unrelated to me!
The following is nonsense and can be skipped.
The usage method is very simple. As long as your beloved computer supports PXE boot function, how to support it, find it in your COMS, I can't explain one by one. What if it doesn't support? Nonsense! If it doesn't support, what's the point of network cloning? However, it's not impossible, just a bit more troublesome. You can add a PXE boot chip, or flash the BOIS code. For specific methods, find relevant materials by yourself. What if there are dozens or hundreds of them? Oh my god, you can't flash one by one. Most current motherboards are integrated with PXEROM, unless it's an old antique.
The specific operation methods are as follows:
1. 1> Set the IP of the network cloning server: 10.1.1.1 Netmask: 255.0.0.0
Advantage: Fast and convenient, no need for any settings on the client, quite good when there are more machines. Disadvantage: Need to modify the server IP and subnet mask.
2> Set the IP and subnet mask of the network cloning server to the current one, and the client automatically performs network cloning by adjusting the WATTCP.CFG configuration file.
Advantage: No need to modify the server IP and subnet mask, good when there are not many machines. Disadvantage: Need to change the client WATTCP configuration for each machine.
3> Set the IP and subnet mask of the network cloning server to the current one, and the client enables manual GHOST to select the session and automatically obtain the IP for network cloning.
Advantage: No need to modify the server IP and subnet mask. Disadvantage: Sometimes unable to find the DHCP service, quite frustrating!
2. Open Tftpd32, keep 2 items, namely (TftpServer, DHCPServer), fill in the starting IP address, and the number of IPs to accommodate \ subnet mask,
The boot file name is mba.pxe Note that the IP address pool must be in the same network segment as the network cloning server IP, otherwise the image cannot be downloaded.
3. Open GhostSrv network cloning server, set the session name to: NET and the image file location. Select the partition or disk according to the situation,
Click to accept the client.
4. The client sets to boot from PXE, downloads the image from the server to the client system, enters the PXE network cloning maintenance system, the first item loads the network card driver, OK, then select the partition or disk to clone.
5. The server receives the client information, clicks to send data, and starts network cloning...
Download address:
http://hulongzhuo.ys168.com
Last edited by hulongzhuo on 2007-7-12 at 02:03 PM ]
