|
aleng18
初级用户
 
积分 50
发帖 7
注册 2005-8-23
状态 离线
|
 『楼 主』:
我发明了,dos启动盘驱动usb2.0优盘,国内领先!
[已使用 LLM 解释]
dos下驱动usb2.0的u盘
车里焖-原创-qq-87175704
很早以前就有dos下启动盘驱动优盘的方法,但那个驱动不了usb2.0的,我作的启动盘方法差不多,但能dos驱动2.0的。
为什么要在dos下驱动usb2.0盘?这是很重要地!
我用它来dos杀毒,当然还可以干很多别的事情。
为什么要在DOS下杀毒?因为很多病毒只有dos下能杀干净
存病毒库,软盘的容量是不够了,病毒库又常更新,把杀毒软件坐在光盘上,很快就淘汰了
dos启动盘启动,加载usb驱动,转到u盘盘符,运行dos杀毒程序!
这个方法比u盘直接启动dos好,不受主板限制。
我有个机子,主板 是 只支持usb1.1的。我原来的u盘也是usb1.1的32M,
这个u盘在 dos下 软盘 驱动方法(编辑config.sys):
device=USBASPI.SYS /// 1。x
device=Di1000dd.SYS /// n年以前的
能用,用了快两年,嫌太小,给我弟了。
我又弄了个usb2.0的128M,又用这张软盘驱动,不行了,我又把 USBASPI.SYS 换成了 2.06 的,还不行。
-----------再强调一遍,以上命令对usb2.0优盘不好用了,-------------------------------------
应该是因为优盘里面的芯片变了.我又下载了 [超级通用MS-DOS 7.10启动盘]据说有n多特点,
也支持dos驱动优盘。我做成了软盘,启动时选择了3和4测试,选3 加载失败,选4死机,加载了太多程序兼容
性不行,我又到别处找方法。但是国内说的都乱七八糟,我也就乱七八糟的试验。瞎弄一顿,居然可以用软盘
在dos下加载(usb2.0)u盘了!!!就是不知道为什么?经过n次失败,终于得出了在usb1.1主板上识别我的u盘
的方法(就是不知道为什么?):
device=duse.exe
device=USBASPI.SYS
device=Di1000dd.SYS
和前面有什么区别?就是多了一个device=duse.exe,并且必须按照上面顺序,国内的启动盘都没有第一个
所以都驱动不了usb2.0优盘,但是现在usb1.1优盘基本没了,对8
我觉得我这个成果达到了国内领先水平!!!因为我在华军等地方下载的所有启动盘都不能驱动我的usb2.0优盘。
其实就是没有这条命令“device=duse.exe”,或者没把以上三条命令,按我的次序排列!
接着,我又把 duse.exe 升级成最新的4.9
-----------必须加上duse.exe-------------------------------------------------------------
那个2.06版的 usbaspi.sys 加上 /e参数就支持usb2.0的主板呢(ehci),大家都测试一下。
Driving USB 2.0 USB flash drives under DOS
Che Li Men - Original - QQ - 87175704
A long time ago, there was a method to start the disk under DOS to drive the USB flash drive, but that one couldn't drive USB 2.0. The method I made is similar but can drive 2.0 under DOS.
Why drive a USB 2.0 drive under DOS? This is very important!
I use it to kill viruses under DOS, and of course, it can do many other things.
Why kill viruses under DOS? Because many viruses can only be completely killed under DOS
The capacity of floppy disks is not enough to store virus databases, and virus databases are often updated. Putting the antivirus software on a CD-ROM will be eliminated quickly
Start the DOS boot disk, load the USB driver, go to the USB drive letter, and run the DOS antivirus program!
This method is better than directly starting DOS from the USB flash drive, not limited by the motherboard.
I have a computer with a motherboard that only supports USB 1.1. My original USB flash drive was also a 32M USB 1.1 one.
This USB flash drive could be used under DOS with the floppy disk driving method (editing config.sys):
device=USBASPI.SYS /// 1.x
device=Di1000dd.SYS /// Many years ago
It worked and I used it for almost two years, but I thought it was too small and gave it to my brother.
I got another 128M USB 2.0 one, and using this floppy disk to drive it didn't work. I then replaced USBASPI.SYS with the 2.06 version, but it still didn't work.
-----------Reemphasize again, the above commands don't work well for USB 2.0 USB flash drives,-------------------------------------
It should be because the chip inside the USB flash drive has changed. I downloaded the which is said to have many features and also supports driving USB flash drives under DOS. I made it into a floppy disk, selected tests 3 and 4 when booting, selected 3 and the loading failed, selected 4 and it froze, and there were too many program compatibility issues. I then looked for methods elsewhere. But what I found in China was all messy, so I also tested messily. After messing around, I actually could load the (USB 2.0) USB flash drive under DOS with a floppy disk!!! I just don't know why? After many failures, I finally got the method to recognize my USB flash drive on the USB 1.1 motherboard (I just don't know why?):
device=duse.exe
device=USBASPI.SYS
device=Di1000dd.SYS
What's the difference from before? It's just that there's an additional device=duse.exe, and it must be in the above order. Domestic boot disks all don't have the first one, so they can't drive USB 2.0 USB flash drives. But now USB 1.1 USB flash drives are basically gone, for 8
I think my achievement has reached the domestic leading level! Because all the boot disks I downloaded from Huajun and other places can't drive my USB 2.0 USB flash drive.
In fact, it's just that there's no command "device=duse.exe", or the above three commands are not arranged in my order!
Then, I upgraded duse.exe to the latest 4.9
-----------Must add duse.exe-------------------------------------------------------------
The 2.06 version of usbaspi.sys plus the /e parameter supports USB 2.0 motherboards (ehci), everyone can test it.
此帖被 +2 点积分 点击查看详情 评分人:【 】 | 分数: +1 | 时间:2007-5-14 16:03 | 评分人:【 hhwwll 】 | 分数: -2 | 时间:2008-3-30 00:48 | 评分人:【 147447627 】 | 分数: +1 | 时间:2008-4-11 19:07 | 评分人:【 】 | 分数: +1 | 时间:2010-3-22 20:15 | 评分人:【 】 | 分数: +1 | 时间:2010-9-16 11:26 |
|
LLM 解释
关于DOS下驱动USB2.0优盘的技术分析
1. 背景与问题提出
在DOS环境下使用USB2.0优盘存在挑战,传统的针对USB1.1优盘的驱动方法在面对USB2.0优盘时可能失效。例如用户之前使用基于USB1.1的32M优盘时,通过编辑config.sys 文件添加device=USBASPI.SYS 和device=Di1000dd.SYS 等命令可以正常驱动,但更换为USB2.0的128M优盘后,原来的命令不再生效。
2. 关键驱动文件与顺序
-
duse.exe:是关键的驱动文件之一。用户发现,在
config.sys 中按照device=duse.exe 、device=USBASPI.SYS 、device=Di1000dd.SYS 的顺序添加设备驱动时,能够在USB1.1主板上识别USB2.0优盘。而国内很多其他启动盘没有包含duse.exe 或者没有按照正确顺序排列这些驱动文件,导致无法驱动USB2.0优盘。
-
USBASPI.SYS:对于USB2.0主板,可能需要对
USBASPI.SYS 加上/e 参数来支持EHCI(Enhanced Host Controller Interface,增强型主机控制器接口),从而实现对USB2.0设备的更好支持。
-
Di1000dd.SYS:这也是早期用于存储设备相关驱动的文件之一,需要按照上述正确顺序与其他驱动文件配合使用。
3. 应用场景与优势
在DOS下驱动USB2.0优盘主要应用于DOS杀毒等场景。因为很多病毒在DOS下才能被彻底查杀,而将杀毒软件相关文件存储在USB2.0优盘并通过DOS启动盘加载驱动后,可以方便地进行杀毒操作。相比优盘直接启动DOS,这种方法不受主板是否支持USB2.0的限制,对于一些仅支持USB1.1的主板也能实现对USB2.0优盘的使用。
代码示例(config.sys文件内容示例)
device=duse.exe ; 加载duse.exe驱动
device=USBASPI.SYS ; 加载USBASPI.SYS驱动,可根据需要添加/e参数如device=USBASPI.SYS /e
device=Di1000dd.SYS ; 加载Di1000dd.SYS驱动
需要注意的是,在DOS环境下的驱动配置需要根据具体的硬件和软件环境进行细致调整,不同的主板、优盘芯片等可能需要不同的驱动组合与参数设置。
附件
1: dos下驱动usb2u盘.rar (2005-9-1 22:56, 73.33 KiB, 下载附件所需积分 1 点
,下载次数: 5446)
|
|
2005-9-1 22:56 |
|
|
quanyongji
初级用户
 
积分 161
发帖 35
注册 2005-2-9
状态 离线
|
『第 2 楼』:
使用 LLM 解释/回答一下
首先 你要有个软驱,好用的!
其次有个软盘,没坏道的!
这个软盘还要是win98启动盘,能用它启动电脑的!
然后,把我的这几个文件复制进去,替换!
然后插上usb2.0优盘,确认此优盘在windows2000,xp,2003下是好用的
然后,用软盘启动,看能出u盘盘符码?里面的程序能看见吗?
如果不能出现盘符,请向我说明你的u盘品牌型号,主板型号!
不知道超级dos7.1下能用吗?
First of all, you need to have a floppy drive, a good one!
Second, have a floppy disk, without bad sectors!
This floppy disk also needs to be a Win98 boot disk, which can be used to boot the computer!
Then, copy these few files of mine in and replace them!
Then plug in a USB 2.0 flash drive, and confirm that this flash drive is usable under Windows 2000, XP, 2003
Then, boot with the floppy disk and see if the USB drive letter can appear? Can the programs inside be seen?
If the drive letter cannot appear, please tell me the brand and model of your USB drive and the model of the motherboard!
I wonder if it can be used under Super DOS 7.1?
|

CPU AMD 939 3200+
NF4UK8AA
ST380013AS SATA
KINGMAX DDR400 512*2
x1300xt
win98启动u盘(4g)WINdows2008r2 |
|
2005-9-3 21:39 |
|
|
aleng18
初级用户
 
积分 50
发帖 7
注册 2005-8-23
状态 离线
|
『第 3 楼』:
最新版本的usbmass在我这不好用,我做的就好用!
使用 LLM 解释/回答一下
usbmass=http://www.tssc.de/download/download.htm
另外 由于nf2芯片组的天生缺陷,很多usb功能在那主板上试验失败,这不怪我。你的主板如果是nf2芯片组,恭喜你,中了;-)
usbmass=http://www.tssc.de/download/download.htm
Additionally, due to the inherent defects of the nf2 chipset, many USB functions failed to work on that motherboard, and it's not my fault. If your motherboard is of the nf2 chipset, congratulations, you've got it; -)
|
|
2005-9-3 23:50 |
|
|
Michael
钻石会员
       
积分 10046
发帖 3039
注册 2002-11-11
状态 离线
|
『第 4 楼』:
使用 LLM 解释/回答一下
传输率多少?能达到读3M/s,写1M/s吗?
What's the transfer rate? Can it reach 3M/s for reading and 1M/s for writing?
|

简单就是美 |
|
2005-9-4 00:10 |
|
|
sodohe
新手上路

积分 6
发帖 4
注册 2005-9-25
状态 离线
|
|
2005-9-25 05:46 |
|
|
gongchengxi
初级用户
 
积分 40
发帖 20
注册 2005-11-16
状态 离线
|
|
2005-11-17 14:00 |
|
|
ssbc
新手上路

积分 8
发帖 2
注册 2006-3-9
状态 离线
|
『第 7 楼』:
使用 LLM 解释/回答一下
谢谢楼猪,偶下载测试一下
Thanks, LZ. I'll download and test it.
|
|
2006-7-23 15:56 |
|
|
ayacn2000
新手上路

积分 4
发帖 2
注册 2006-7-25
状态 离线
|
『第 8 楼』:
使用 LLM 解释/回答一下
楼主强淫,我试试能不能驱动我的移动硬盘先。
The LZ is an awesome person, I'll try to see if I can get my external hard drive to work first.
|
|
2006-7-25 10:44 |
|
|
broimoise
新手上路

积分 12
发帖 6
注册 2006-7-9
状态 离线
|
|
2006-7-26 20:42 |
|
|
sayes
初级用户
 
积分 20
发帖 8
注册 2006-7-27
状态 离线
|
『第 10 楼』:
使用 LLM 解释/回答一下
刚试了USBMASS,不行。谢谢这个。下载试一下。。
Just tried USBMASS, it didn't work. Thanks for this. Download and try it.
|
|
2006-7-27 20:20 |
|
|
agood2003
新手上路

积分 8
发帖 2
注册 2006-8-4
状态 离线
|
『第 11 楼』:
使用 LLM 解释/回答一下
下载测试不能出现盘符
品牌型号:scandisk cruzer mini
主板型号:asus cuv4x-e
Download test should not have drive letters.
Brand model: scandisk cruzer mini
Motherboard model: asus cuv4x - e
|
|
2006-8-8 15:44 |
|
|
nicplan
新手上路

积分 2
发帖 1
注册 2007-3-11
状态 离线
|
|
2007-3-11 02:48 |
|
|
Ancient
新手上路

积分 2
发帖 1
注册 2007-2-28
状态 离线
|
|
2007-3-11 03:08 |
|
|
wurong
初级用户
 
积分 110
发帖 2
注册 2002-12-13
状态 离线
|
『第 14 楼』:
使用 LLM 解释/回答一下
发现了还是发明了。
真的发现了?
Discovered or invented.
Really discovered?
|
|
2007-3-11 09:09 |
|
|
liangqi
初级用户
 
积分 135
发帖 12
注册 2003-7-18
状态 离线
|
『第 15 楼』:
我的USB 2.0在硕泰克主板上无法启动
使用 LLM 解释/回答一下
我的 usb 是2.0的,在硕泰克主板上能够传递文件,我也做成了启动u盘,在另一台845主板上能够引导,就是在硕泰克主板上无法引导。根据楼主的方法做了启动软盘,引导以后,还是无法识别。
屏幕显示如下:
USB Drive support enabled
Drive I : <Not Installed>
ASPI D device : ID : 0 LUN : 0 = SZHX SKYMEDI 1.00
DI1000 ASPI DISK Driver Ver 2.00
Availeble ID = 0
ID 0 = HD .. SZHX SKYMEDI
#1 : ??? _(光标闪烁)
没能继续下去。
请高手指点。
My USB is 2.0. It can transfer files on the Soltek motherboard, and I also made it into a bootable USB drive. It can boot on another 845 motherboard, but it can't boot on the Soltek motherboard. I made a bootable floppy disk according to the landlord's method, but after booting, it still can't be recognized.
The screen display is as follows:
USB Drive support enabled
Drive I : <Not Installed>
ASPI D device : ID : 0 LUN : 0 = SZHX SKYMEDI 1.00
DI1000 ASPI DISK Driver Ver 2.00
Availeble ID = 0
ID 0 = HD .. SZHX SKYMEDI
#1 : ??? _ (The cursor is flashing)
Couldn't continue.
Please give advice from the experts.
|
|
2007-3-12 04:46 |
|