标题: 转贴自网易社区：DOS下面的USB设备用起来可真不容易 [打印本页]
作者: MYS 时间: 2002-10-17 00:00 标题: 转贴自网易社区：DOS下面的USB设备用起来可真不容易
作 者: lastlooking(回眸一笑)
下载了一个DOS下面USB设备的驱动程序DUSE，加载后重新启动进入DOS系统，移动硬盘到是找到了，可惜扇区无法正确读取，因为驱动程序能识别的扇区大小为512、1024、2048，而我的移动硬盘扇区大小为8192，郁闷郁闷。。。。
作者: Wengier 时间: 2002-10-17 00:00
要是在这儿问就最好不过了。
作者: qngqng 时间: 2002-10-24 00:00
我也遇到这样的问题，在DOS下可以找到盘符，就是无法读取请问如何办？
作者: Wengier 时间: 2002-10-24 00:00
那您那个USB设备具体的情况如何？是何种USB设备？
作者: qngqng 时间: 2002-10-24 00:00
usb1.1 移动硬盘
作者: Wengier 时间: 2002-10-24 00:00
可能需要一些参数才可以正常加载，具体参数可在“DOS文章”栏目中看到：
http://www.cn-dos.net/newdos/dosarticle.html
另外，您不妨试试新加入的USB驱动程序“Motto Hairu”，它也可以驱动USB硬盘：
http://www.cn-dos.net/newdos/doswarec.html
作者: fbair 时间: 2002-10-31 00:00
我想买个U盘，在dos下可以驱动吗？使用那个驱动？有usb驱动马？可以运行里面的program?
作者: MYS 时间: 2002-10-31 00:00
目前U盘不能在DOS下驱动，除非是用U盘启动的DOS。
作者: Wengier 时间: 2002-11-1 00:00
U盘是USB磁盘吗？
作者: rrdn 时间: 2002-11-1 00:00
我的USB 光驱也能找到盘符，但不能读取内容。
是笔记本芯的USB光驱，不是那种台式机的，超薄型的，不知怎么设置可以驱动，弄了一天也没有搞定。
作者: MYS 时间: 2002-11-1 00:00
U盘是拇指大小的FLASH电子盘，就是朗科优盘，爱国者迷你盘之类的。
rrdn，或者你研究一下它的参数，我这里没有USB驱动器，无法试验。光盘的每个簇好象应该是2048字节的。
作者: Wengier 时间: 2002-11-1 00:00
另外还可以试试USB_CD和Motto Hairu以驱动USB光驱。
作者: 0122 时间: 2002-11-5 00:00
如何使用Motto Hairu以驱动USB硬盘
作者: Wengier 时间: 2002-11-5 00:00
Motto Hairu里面有三个驱动程序，分别为USB的ASPI管理器、软盘、硬盘的驱动程序，具体可见里面的说明文件。
作者: Wengier 时间: 2002-11-5 00:00
以下是Motto Hairu的英文说明：
----------
"motto hairu" DOS Driver
----------
This driver enables "motto hairu" USB interface on DOS.
IEEE1394 interface can not be used on DOS.
There are three drivers as DOS Driver.
USBASPI.SYS : USB1.1 mode ASPI Manager
RAMFD.SYS : RAM DISK driver for USB floppy, if you have only single USB port and access both.
Di1000dd.SYS : ASPI HDD driver
1. If you does not have USB floppy
Copy USBASPI.SYS and Di1000dd.SYS files and
add following 2 lines to config.sys on the boot disk.
device=USBASPI.SYS
device=Di1000dd.SYS
After that, connect "motto hairu" to USB port, then set this disk to FDD, and
power-on PC.
2. If you use USB floppy
Copy USBASPI.SYS, Di1000dd.SYS and RAMFD.SYS files and
add following 3 lines to config.sys on the boot disk.
device=RAMFD.SYS
device=USBASPI.SYS /W --- Use /R option, if you have multiple USB ports
device=Di1000dd.SYS
And confirm
device=himem.sys
is exist in config.sys.
If you don't have, add following 4 lines.
device=himem.sys
device=RAMFD.SYS
device=USBASPI.SYS /W
device=Di1000dd.SYS
When power-on, during booting, contents of FD is copied to RAM disk, then,
when the copy is completed, following message will appear.
===============================================
=== Connect the target device to USB port. ===
=== Press [ENTER} to continue. ===
===============================================
Then, disconnect USB floppy from USB port and connect "motto hairu" to USB port and
press [ENTER] key.
Boot will continue from RAM disk.
NOTE:
1) After changing DOS mode with rebooting Windows, it can not work.
You must power off once.
2) Option settings
USBASPI.SYS has following options.
/R : Access also USB FDD.
: RAMFD.SYS may be needed in some cases.
/W : Prompt following message for swapping floppy and device, if you need to boot from USB floppy and have only one USB port.
===============================================
=== Connect the target device to USB port. ===
=== Press [ENTER} to continue. ===
===============================================
/M=xx : OHCI memory map address
As default, it will use unused address between D0000h and DFFFFFh.
Ex) /M=D4 : Use D4000h
/P=xxx0 : UHCI I/O address
Specify if BIOS does not assign I/O Port Address of the controller.
/V : Shows various information.
3) In case of OHCI, EMM386.EXE is not recommended.
If you use it, don't use UMB or specify X=D000-DFFF to keep extended ROM space.
4) In some PC, UHCI's I/O port is not assigned by BIOS.
In this case, specify I/O port by /P option.
Appendix - About OHCI and UHCI
There are two kind of USB host controller chip spec.
Universal Host Controller Interface = UHCI
Open Host Controller Interface = OHCI
We can check which is used by following procedure.
1. Click [Start] -> [Setting(S)] -> [Control Panel(C)].
2. Double click [System] icon.
3. Click [Device Manager] tab.
4. Double click [Universal Serial Bus Controller].
************* Universal Host Controller
means UHCI is used.
************* Open Host Controller
means OHCI is used.
作者: 0122 时间: 2002-11-6 00:00
看了上面的说明.我还是不太清楚.你能据一个实际超作的例子让我参考一下吗.比如说我用的是IBM--USB1.1硬盘.应该如何做.还有一个问题是关于DUSE的.想请教一下.我在DOS下输入c:\duseldr.com c:\duse.exe
运行后得到
DUSE version 4.2 Build 65 (general)
DOS USB Stack with USB Storage Extensions
Copyright Cypress Semiconductor, 2000-20002
UHCI USB Controller initialized[I/O 0X600, IRQ 9]
UHCI USB Controller initialized[I/O 0X640, IRQ 9]
............
此时硬盘的指示灯亮起.{这是不是说明硬盘已被驱动,如果是的话下面我该如何做}
同时我的键盘失效,不能进行认何超作.{请问是何原因}
作者: 禅宗 时间: 2002-11-7 00:00
我就是用这个命令就可以驱动我的爱国者存储王啊，我想可能不是软件的问题，应该是USB硬盘电压的问题！