|
lj6384320
新手上路
积分 12
发帖 4
注册 2006-4-19
状态 离线
|
『楼 主』:
如何在DOS环境下升级BIOS?急！！！
使用 LLM 解释/回答一下
各位大虾，小弟有MS-DOS 7.10超级启动盘一张，并将升级文件存入C盘，进入DOS环境后，如何找到C盘上的BIOS升级文件？
请问大虾：如何在DOS环境下找到C盘上的BIOS升级文件，进行BIOS刷新。能否告知详细的过程？小弟不慎感激！先在此谢谢了！
Dear experts, I have a MS-DOS 7.10 super boot disk, and I have stored the upgrade file in drive C. After entering the DOS environment, how to find the BIOS upgrade file on drive C?
May I ask experts: How to find the BIOS upgrade file on drive C in the DOS environment to perform BIOS flashing. Can you tell me the detailed process? I would be very grateful! Thank you in advance!
|
|
 2006-4-19 19:15 |
|
|
chujiafu
银牌会员
积分 1339
发帖 595
注册 2004-5-26
来自 安徽 宿州
状态 在线
|
『第 2 楼』:
使用 LLM 解释/回答一下
最好不要刷新，如一定刷新，请一高手指导。
It is best not to refresh. If you must refresh, please have an expert guide.
|
|
|
2006-4-19 19:18 |
|
|
lj6384320
新手上路
积分 12
发帖 4
注册 2006-4-19
状态 离线
|
『第 3 楼』:
使用 LLM 解释/回答一下
谢谢上楼大虾的提醒;
我在网上找到了如何刷bios的视频教程。就是不知道如何在DOS环境下找到C盘上的BIOS升级文件？在DOS环境下只出现： A：<\
不知需键入什么命令才能浏览C盘上的文件？
先谢谢了！
Thanks to the reminder from the senior upstairs;
I found a video tutorial on how to flash the BIOS online. Just don't know how to find the BIOS upgrade file on the C drive in the DOS environment? In the DOS environment, only: A: <\ appears
I don't know what command to type to browse the files on the C drive?
Thanks in advance!
|
|
|
2006-4-19 19:40 |
|
|
store88
中级用户
积分 416
发帖 125
注册 2005-6-9
状态 离线
|
『第 4 楼』:
使用 LLM 解释/回答一下
bios升级文件已经在你的硬盘上面了吗
Is the BIOS upgrade file already on your hard drive?
|
|
|
2006-4-19 21:05 |
|
|
wl00560
银牌会员
积分 1384
发帖 709
注册 2005-10-29
状态 离线
|
『第 5 楼』:
使用 LLM 解释/回答一下
你非要刷就刷吧，出问题了不要找我^_^
首先，你要知道你的bios叫什么名字（一定要与主板主板匹配）
然后，输入bios刷新程序的名字，可以不要加任何参数
然后会出现一个图形界面。让你输入bios的名字，你就输入c:\bios的名字（c:\是告诉程序到c盘找你的bios文件）
然后程序会问你保存bios否，建议保存一下，如a:\old.bin（即保存在软驱中）
然后就刷吧，祈祷不会停电，不会出任何问题。这时会有一条白线一直向前动，你最好不要动电脑。
最后刷新程序会告诉你按f1重启动，是闪动的字（在这之前，千万不可重启），重启后就成功了。
提醒一句，刷bios是很危险的。楼主好像对dos不是很熟悉，不知英文怎样？如果英文不行，就抱本字典。千万要弄明白屏幕上的意思，再进行刷新，否则后果很严重哦。
If you really want to flash, go ahead. If there's a problem, don't come to me ^_^
First, you need to know the name of your BIOS (it must match the motherboard).
Then, enter the name of the BIOS flashing program, and you can don't add any parameters.
Then a graphical interface will appear. When it asks you to enter the name of the BIOS, you just enter the name of the BIOS in c:\ (c:\ tells the program to find your BIOS file on the C drive).
Then the program will ask if you want to save the BIOS. It is recommended to save it, such as a:\old.bin (that is, save it in the floppy drive).
Then just flash it, and pray that there will be no power outages and no problems. At this time, there will be a white line moving forward all the time. You'd better not move the computer.
Finally, the flashing program will tell you to press F1 to restart, which is flashing text (before this, you must not restart). After restarting, it will be successful.
One reminder: Flashing the BIOS is very dangerous. The owner seems not very familiar with DOS. I don't know how about English? If English is not good, just hold a dictionary. Be sure to understand the meaning on the screen before flashing, otherwise the consequences will be serious oh.
|
|
|
2006-4-19 21:27 |
|
|
雨露
管理员
DOS非常爱好者
积分 6209
发帖 2598
注册 2006-1-20
状态 离线
|
『第 6 楼』:
防范于未然,万一失败了,可先做好这个准备工作,不是我咒你
使用 LLM 解释/回答一下
问：刷新BIOS失败，应该如何处理？
答：其实，刷新主板BIOS是很危险的，常见的修复方法一般有以下几种：
一、Award BIOS中固化了一个Boot Block程序，它一般不会被刷新软件刷新。因此即使BIOS刷新失败，Boot Block还是能够控制ISA显卡与软驱。但是现在多数主板不支持ISA，所以还是利用软驱吧！
首先做一张系统盘，删去里面的Config.sys和Autoexec.bat，再把正确的BIOS更新程序和数据文件拷到系统盘。然后在系统盘中建立Autoexec.bat，并加入：Awdflash xxx.bin /f /sn /py /r（xxx.bin是BIOS数据文件）。其中的/f /sn /py /r参数表示不备份而仅仅更新BIOS后自动重启。 当刷新失败时，插入此盘重新启动，系统会自动地更新BIOS，等数分钟后再重新启动，一般BIOS就可以恢复了。
二、如果损坏比较严重，连Boot Block引导块也一起损坏，可以试用“热插拔”来修复。当BIOS完成POST上电自检、系统启动自举程序后，由操作系统接管系统的控制权。完成启动过程后，BIOS已完成了它的使命，之后它基本是不工作的。
首先放掉身上的静电，找到一台与已坏主板相同型号的主板(以下简称“好主板”)，分别拔出两块主板的BIOS芯片，然后将好主板的BIOS芯片插回BIOS插座，注意不能插得太紧，只要引脚能刚刚接触到插座即可。启动电脑，进入纯DOS状态，将好BIOS芯片拨出来，再将坏BIOS芯片插到该主板上，进行BIOS刷新，问题就可以解决了.
Q: The BIOS flash failed. How should I handle it?
A: Actually, flashing the motherboard BIOS is very dangerous. The common repair methods are generally as follows:
1. An Award BIOS has a Boot Block program固化 in it, which is generally not refreshed by the flash software. Therefore, even if the BIOS flash fails, the Boot Block can still control the ISA graphics card and the floppy drive. But now most motherboards do not support ISA, so still use the floppy drive!
First, make a system disk, delete Config.sys and Autoexec.bat in it, and then copy the correct BIOS update program and data file to the system disk. Then, create Autoexec.bat in the system disk and add: Awdflash xxx.bin /f /sn /py /r (xxx.bin is the BIOS data file). The parameters /f /sn /py /r mean to update the BIOS automatically and restart without backing up. When the flash fails, insert this disk and restart, the system will automatically update the BIOS. Wait for a few minutes and then restart, generally the BIOS can be restored.
2. If the damage is relatively serious and even the Boot Block boot block is damaged together, you can try to repair it by "hot plugging". After the BIOS completes the POST power-on self-test and the system starts the bootstrap program, the operating system takes over the control of the system. After the boot process is completed, the BIOS has completed its mission, and then it basically does not work.
First, release the static electricity on your body, find a motherboard of the same model as the bad motherboard (hereinafter referred to as "good motherboard"), respectively pull out the BIOS chips of the two motherboards, then insert the BIOS chip of the good motherboard back into the BIOS socket, pay attention not to insert it too tightly, as long as the pins can just touch the socket. Start the computer, enter the pure DOS state, pull out the good BIOS chip, and then insert the bad BIOS chip into the motherboard, and perform BIOS flashing, the problem can be solved.
|
|
|
2006-4-19 21:59 |
|
|
lj6384320
新手上路
积分 12
发帖 4
注册 2006-4-19
状态 离线
|
『第 7 楼』:
使用 LLM 解释/回答一下
谢谢各位大虾的热心帮忙，小弟在此谢谢了。
Thank you, esteemed seniors, for your enthusiastic help. I thank you here.
|
|
|
2006-4-19 22:29 |
|
|
xuantian
高级用户
积分 587
发帖 282
注册 2006-4-10
状态 离线
|
『第 8 楼』:
使用 LLM 解释/回答一下
我看你还是免了吧
热狗实在要刷新,建议你
1. 制作一张可引导的软盘,将主板的原bios文件和刷新程序备用.
2. 刷新时千万不要刷新 Biso 的引导块.
3. 如果刷新失败, 插入备份的软盘, 然后刷入原来的bios (只要升级时不刷新引导块, Bios 刷新失败后一样可以使用引导块将主板引导到软驱上)
4. 再次提醒, 除非你有绝对的把握, 不要尝试刷新 Bios 的引导块!!!
I see you'd better forget it.
If you really need to refresh the hotdog, it is suggested that you:
1. Make a bootable floppy disk and have the original BIOS file of the mainboard and the refresh program as backups.
2. Never refresh the boot block of the BIOS when refreshing.
3. If the refresh fails, insert the backup floppy disk and then flash the original BIOS (as long as the boot block is not refreshed during the upgrade, the boot block can still be used to boot the mainboard to the floppy drive even if the BIOS refresh fails).
4. Remind again, do not attempt to refresh the boot block of the BIOS unless you are absolutely sure!!!
|
|
|
2006-4-20 00:05 |
|
|
fujianabc
金牌会员
积分 3467
发帖 1616
注册 2004-6-21
状态 离线
|
『第 9 楼』:
使用 LLM 解释/回答一下
现在大部分主板都支持在windows下刷新bios的，没必要再在dos下用软驱刷新了。
Now most motherboards support flashing the BIOS under Windows, so there's no need to flash it with a floppy drive under DOS anymore.
|
|
|
2006-4-20 10:45 |
|
