『楼 主』:
IBM OS/2 Warp4 简体中文光盘版的安装方法！
使用 LLM 解释/回答一下
IBM OS/2 Warp4 简体中文光盘版不能光盘启动。我在网上找了好久也没有找到安装方法。偶然发现可以这样安装的:
1.先在一台电脑上安装MSDOS6。22系统和光驱动，在DOS下进入光驱所在盘符，执行光盘目录下的某个命令，是带CD或MAK开头的批处理吧，都可以的（不好意思！现在光盘放在家里，只能回忆一个大概），放入三张空软盘，分别制作#1，#2，SETUP三个安装软盘。在执行光盘目录下的批处理命令前，最好执行一下中文字库如TWAY32.EXE,否则有乱码出现!
2.将一块要安装OS/2的硬盘格式化为FAT16.分区2GB,内存16MB即可.如果现在不分区,以后安装只能选择是"高级安装"不可以是"简易安装"了.
3.放入SETUP安装软盘,启动电脑,再放入#1号软盘,回车,放入#2号软盘,最后放入IBM OS/2 Warp4 简体中文光盘,SETUP安装软盘再放一次,重启动,接下来按中文提示,应该很容易了!
以上三张安装软盘(在虚拟机上用1.44MB的IMG软盘映像即可)制作我是在VMWARE虚拟机上完成的,OS/2系统是在Visal PC2004虚拟机上完成的! OS/2 Warp P3光盘版安装方法同上,只是只要二张软盘就够了!祝朋友们安装成功!以上是我的回忆,可能有些地方说得不对,有什么问题,可以发给我
IBM OS/2 Warp 4 Simplified Chinese CD version cannot boot from the CD. I have been searching the Internet for a long time and haven't found the installation method. I accidentally found that it can be installed like this:
1. First, install the MSDOS 6.22 system and the optical drive on a computer. Enter the drive letter where the optical drive is located under DOS, and execute a certain command in the CD directory, which is a batch file starting with CD or MAK, etc., it's all okay (sorry! Now the CD is at home, I can only recall roughly), insert three blank floppy disks, and make #1, #2, and SETUP installation floppy disks respectively. Before executing the batch command in the CD directory, it is best to execute a Chinese font library such as TWAY32.EXE, otherwise garbled characters will appear!
2. Format a hard drive to install OS/2 as FAT16. The partition is 2GB, and the memory is 16MB. If you don't partition now, later installation can only choose "Advanced Installation" and not "Easy Installation".
3. Insert the SETUP installation floppy disk, start the computer, then insert the #1 floppy disk, press Enter, insert the #2 floppy disk, and finally insert the IBM OS/2 Warp 4 Simplified Chinese CD, insert the SETUP installation floppy disk again, restart, and then follow the Chinese prompts, it should be very easy!
The production of the above three installation floppy disks (using a 1.44MB IMG floppy disk image on the virtual machine) was completed on the VMWARE virtual machine, and the OS/2 system was completed on the Visal PC2004 virtual machine! The installation method of the OS/2 Warp P3 CD version is the same as above, but only two floppy disks are needed! Wish friends successful installation! The above is my recollection, there may be some places that are not right, if there are any problems, you can send them to me
|
