标题: 网卡驱动时提示一个文件没有加载，具体如下 [打印本页]
作者: d5love1b 时间: 2005-1-26 00:00 标题: 网卡驱动时提示一个文件没有加载，具体如下
网卡是Marvell Yukon Gigabit Ethernet 10/100/1000Base-T Adapter, Copper RJ-45
启动到dos后加载驱动程序提示The LSL is not loaded，可是驱动程序里边根本没提供这个文件，我觉得是驱动程序里少提供了个什么文件，可是在网上搜索了很久也没找到，谁能指点一二，非常感谢，驱动程序的说明文件如下，其中提到的YUKODI.COM YUKODI.INS NET.CFG 都有
All rights reserved.
===========================================================================
yukodi.txt created 04-Aug-2003
Readme File for yukodi.com v6.06 DOS ODI Driver supporting
the Marvell Yukon Gigabit Ethernet Adapter
This file contains
1 Overview
2 Required Files
3 Installation
4 Driver Parameters
5 Command line arguments
6 Sample Installation/Configuration
===========================================================================
1 Overview
===========
The driver yukodi.com is the Novell ODI 16-bit DOS Client MLID driver
for the Marvell Yukon Gigabit Ethernet Adapter.
***
2 Required Files
=================
YUKODI.COM the driver
YUKODI.INS installation skript for Novell VLM client
NET.CFG SAMPLE configuration file
latest VLM client from Novell
***
3 Installation
===============
When installing the VLM package for DOS follow the steps below to
install yukodi.com:
1. Start the Netware Client Installation.
2. Start the dialog for choosing the driver for your network adapter.
3. Select "OTHER DRIVERS".
4. Enter the path where the files yukodi.com and yukodi.ins are located.
5. Select "Marvell Yukon Gigabit Ethernet Adapter".
6. In the following setup dialog choose your "Frame Type" and the
other parameters.
8. After savig the setup with <F10>, the driver gets installed.
9. Finish the installation of the Netware Client Installation.
10. You can modify the driver parameters later as described in the next
section.
***
4 Driver Parameters
====================
After the installation of the driver, there will be an entry in the
net.cfg in your nwclient installation directory that identifies your
adapter:
LINK DRIVER YUKODI
It is followed by one or more parameters. Beside the standard
parameters from Novell client the driver supports the following
parameters.
Frame type (mandatory)
FRAME <Frame-Type>
This parameter specifies the Ethernet frame types for your network.
Possible values are:
ETHERNET_II
ETHERNET_802.3
ETHERNET_802.2
ETHERNET_SNAP
Bus and device number (optional)
BUSNUM <busnum>
DEVNUM <devnum>
With these parameters you can specify the network adapter the
driver should bind on. This is useful, when there is more than
one adapter in the system.
The bus and device numbers are assigned by the BIOS at boot time. When
the driver is called with the argument '-l' (see below) it shows bus
and device numbers for the supported adapters in the system.
Connection type
CONTYPE <contype>
This parameter can be used to force link speed and duplex mode.
Using other values than AUTO turns off auto-negotiation and is not
recommended.
Possible values are:
AUTO
100FD
100HD
10FD
10HD
Check Link mode
CHECK_LINK
When this parameter has been specified the driver uses the first
supported adapter in the system with a valid link. This parameter
conflicts with BUSNUM and DEVNUM and will be ignored when BUSNUM
and DEVNUM are used. When using CHECK_LINK you can load the driver
only once.
Calling the driver with the argument '-l' (see below) will show
all supported adapters and their link status.
Number of receive and transmit buffers
RECEIVE BUFFERS [1..5]
TRANSMIT BUFFERS [1..5]
These parameters specify how many transmit and receive buffers the
driver shall use. Using more buffers might improve the performance
but the driver will consume more memory.
The sum of receive and transmit buffers cannot be greater than 6.
***
5 Command line arguments
=========================
yukodi.com can be started with the following arguments:
YUKODI - Installs the LAN driver
YUKODI S - Shows status of all resident LAN drivers in memory
YUKODI U - Unloads resident LAN driver from memory
YUKODI ? - Displays help screen
YUKODI L - Lists supported devices with bus and device number and
link status
***
6 Sample Installation/Configuration
====================================
Sample startnet.bat (in the nwclient installation directory):
SET NWLANGUAGE=ENGLISH
C:\NWCLIENT\LSL.COM
C:\NWCLIENT\yukodi.com
C:\NWCLIENT\IPXODI.COM
C:\NWCLIENT\VLM.EXE
Sample net.cfg (in the nwclient installation directory):
Link Driver YUKODI
FRAME ETHERNET_802.2
BUSNUM 2
DEVNUM 1
*** End of Readme file ***
作者: Michael 时间: 2005-2-7 00:00
The computer must load the Link
Support Layer (LSL) before loading the driver
作者: hzdaniel 时间: 2005-2-7 00:00
此文件我有,但不知道怎樣給你
作者: d5love1b 时间: 2005-2-16 00:00
加载了LSL.COM，可是网络还是不通，无法进行网克，请高手指点一下