我有“启动易Easy Boot 4.56"制作winme和winxp双启动光盘时，将原启动易Easy Boot 4.56\disk1\ezboot\setup98.img改为同路径下的setupme.img后在VMware Workstation中安装winme时出现'Devio driver not found:'OEMD001'.No valid CDROM device drivers selected The windows Me setup filds were not found"的错误提示后回到A：\，我不知如何修改setupme.img,请予指导我等初学DOS的新手，我在此再次谢谢各位DX了！
我的setupme.img中的autoexec,bat的内容如下：
@ECHO OFF
set EXPAND=YES
SET DIRCMD=/O:N
cls
set temp=c:\
set tmp=c:\
path=a:\;%CDROM%:\

IF "%config%"=="NOCD" GOTO QUIT
LH MSCDEX.EXE /D<img src="images/smilies/face-surprise.png" align="absmiddle" border="0">emcd001 /L:%CDROM%

echo.
IF "%config%"=="SETUP_CD" goto AUTOSETUP
GOTO QUIT

:AUTOSETUP
set CDROM=FOO23
FINDCD.EXE
if "%CDROM%"=="FOO23" goto NOCDROM
path=a:\;%CDROM%:\
%CDROM%
cd \WINME
echo.
OEMSETUP.EXE /K "/IE /NF"
goto QUIT

:NOCDROM
echo.
echo The Windows Me Setup files were not found.
echo.

:QUIT

我的config.sys的内容如下:


menuitem=SETUP_CD, Start Windows Me Setup from CD-ROM.
menuitem=CD, Start computer with CD-ROM support.
menuitem=NOCD, Start computer without CD-ROM support.
menudefault=SETUP_CD,30
menucolor=7,0


device=oakcdrom.sys /D<img src="images/smilies/face-surprise.png" align="absmiddle" border="0">emcd001
device=btdosm.sys
device=flashpt.sys
device=btcdrom.sys /D<img src="images/smilies/face-surprise.png" align="absmiddle" border="0">emcd001
device=aspi2dos.sys
device=aspi8dos.sys
device=aspi4dos.sys
device=aspi8u2.sys
device=aspicd.sys /D<img src="images/smilies/face-surprise.png" align="absmiddle" border="0">emcd001
devicehigh=ramdrive.sys /E 2048


device=oakcdrom.sys /D<img src="images/smilies/face-surprise.png" align="absmiddle" border="0">emcd001
device=btdosm.sys
device=flashpt.sys
device=btcdrom.sys /D<img src="images/smilies/face-surprise.png" align="absmiddle" border="0">emcd001
device=aspi2dos.sys
device=aspi8dos.sys
device=aspi4dos.sys
device=aspi8u2.sys
device=aspicd.sys /D<img src="images/smilies/face-surprise.png" align="absmiddle" border="0">emcd001
devicehigh=ramdrive.sys /E 2048


devicehigh=ramdrive.sys /E 2048


files=60
buffers=20
dos=high,umb
stacks=9,256
lastdrive=z
再次请大家一定帮帮我，谢谢！

另:我用记事本将setup98中的Jo.sys中的"98"改为"Me后",用此软盘启动后灰屏(屏上也无任何显示内容),不知为何?请各位DX指点.谢谢!

这样改怎么行？？对于初学者而言，最好不要改。

谢谢Wengier!那应怎样改?教教我吧!谢谢!

你的意思是说同一个IMG 文件,同时存在 WINME 和 WIN98 , 当启动这IMG 文件时, 可以选择 WINME 或者 WIN98 , 那你最好还是分开两个版本的 WINME/98 .

还有, 如果你一定这样做, 我想只能 造 IMG 2.88MB 然后各自添加 WINME/98 启动文件,分目录, 真的是很麻烦!

谢谢各位!第一问题我已解决,我的AUTOXEXC.BAT内容如下:
@ECHO OFF
set EXPAND=YES
SET DIRCMD=/O:N
cls
set temp=c:\
set tmp=c:\
path=a:\;%CDROM%:\

IF "%config%"=="NOCD" GOTO QUIT
LH MSCDEX.EXE /D<img src="images/smilies/face-surprise.png" align="absmiddle" border="0">emcd001 /L<img src="images/smilies/face-smile-big.png" align="absmiddle" border="0">

echo.
IF "%config%"=="SETUP_CD" goto AUTOSETUP
GOTO QUIT

:AUTOSETUP
FINDCD.EXE
path=a:\;%CDROM%:\
%CDROM%
cd \WINME
echo.
OEMSETUP.EXE /K "/IE /NF"
goto QUIT

:NOCDROM
echo.
echo The Windows Me Setup files were not found.
echo.

:QUIT
其中的FINDCD.EXE是,改用本站提供的修后的,非原WINME中的FINDCD.EXE.
但第二个问题仍未解决,请DX们指点指点,谢谢!